Models > DVLR223GG8WW

DVLR223GG8WW General Electric Dryer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for DVLR223GG8WW

Viewing 5 of 5

Manuals & Guides for DVLR223GG8WW

Click to download
Keep searches simple, eg. "belt" or "pump".
This single drum bearing slide is an OEM approved replacement part for dryers. It can also be known as a bearing drum slide, pad, or glide. The slides attach to the inner most slots on the front beari...
In Stock
Order now and your part arrives by Mar 19
This single drum bearing slide attaches to the outer-most side of the bearing. This part is also sometimes referred to as a drum slide, drum glide, or drum pad. It provides support to the front of the...
In Stock
Order now and your part arrives by Mar 19
This 89.5-inch drive belt is for dryers. It has a 4-rib design on the inside for a better grip. If comparing the size of your current belt to the new one, keep in mind that a small amount of stretchin...
In Stock
Order now and your part arrives by Mar 19
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromis...
In Stock
Order now and your part arrives by Mar 19
If the timer knob has broken off your dryer, it is important to replace it so that you are able to properly use your appliance. The plastic can become brittle with age, and with regular use the knob c...
In Stock
Order now and your part arrives by Mar 19
The lint filter is an important component of your dryer, as it traps lint and other debris from entering the dryer vents, where they can become a fire hazard. If your lint filter has become damaged or...
In Stock
Order now and your part arrives by Mar 19
This rear drum bearing kit is a genuine OEM replacement for your dryer. The kit includes a shaft, ground strap, bracket, bearing and seven screws for installation. The bearing supports that back of th...
In Stock
Order now and your part arrives by Mar 19
This part is on the outer door of the dryer.
In Stock
Order now and your part arrives by Mar 19
This push-to-start switch is a genuine OEM part and is used to activate your dryer. If your dryer will not start, or will only start if the switch is pushed down, or the timer knob is not engaging wit...
In Stock
Order now and your part arrives by Mar 19
This lint chute assembly helps guide airflow from the dryer drum to the blower wheel and holds the lint filter. It fits GE and Hotpoint dryers and helps improve drying performance while reducing the r...
In Stock
Order now and your part arrives by Mar 19
$20.95
This Genuine OEM door latch is designed for use with a wide range of GE clothes dryers. Constructed from a combination of durable metal and plastic, the latch is mounted onto the dryer frame to secure...
In Stock
Order now and your part arrives by Mar 19
This rear drum bearing sleeve supports the dryer drum and helps it rotate smoothly. It’s a common fix for noisy dryers or drums that wobble or stop turning. Compatible with select GE and Hotpoint mode...
In Stock
Order now and your part arrives by Mar 19

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for DVLR223GG8WW

Viewing 12 of 12
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Marks left on clothes
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door won’t close
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Drum Not Spinning
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Won’t Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Too hot
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Timer Not Working
Fixed by these parts
Fixing
How to fix it
Door Pops Open
Fixed by these parts
Fixing Fixing
How to fix it
Touchpad does not respond
Fixed by these parts
Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing
How to fix it
Not Heating
Fixed by these parts
Fixing
How to fix it
Heat stays on after drum has stopped
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Matthew from Plainfield, IL
Parts Used:
WE09X27634, WE03X37317, WE03X37318
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy.
803 of 915 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Adrian from Middletown, MD
Parts Used:
WE03X29897
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Drum belt broke
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on.
This was a first attempt ever at fixing an appliance and it was no big deal.
207 of 306 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chad from Gilbert, SC
Parts Used:
WE09X27634, WE14X25080
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
original duct was broken
Dear PartSelect.com,

My repair went off without a hitch.

2 screws removed to remove top.
4 screws removed from inside to remove front panel w/ door.
4 screws removed from top of control panel, loosed and popped top right off.
Flathead screwdriver to pop off old plastic panel.
Removed old wire chas e (plastic, approx 3” long).
Removed built-up lint, wiped down area for new duct.
Snapped new duct on.
Dryer works like new!!
Took about 35 minutes, most of time spent cleaning up inside of dryer from lint due to broken duct.

One problem was that salesperson sold me on a new felt strip to go with new duct. That felt comes already installed on the new duct so I did not need it. Cost me a few extra dollars I did not need to spend.

Other than that, easy ordering, fast shipment, and parts are as close to original as possible.

Thanks for all your help!
142 of 164 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!