Models > DPVH880GJ2WW

DPVH880GJ2WW General Electric Dryer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for DPVH880GJ2WW

Viewing 7 of 7

Manuals & Guides for DPVH880GJ2WW

Click to download
Keep searches simple, eg. "belt" or "pump".
This single drum bearing slide attaches to the outer-most side of the bearing. This part is also sometimes referred to as a drum slide, drum glide, or drum pad. It provides support to the front of the...
In Stock
Order within the next 49 mins and your part ships today!
This single drum bearing slide is an OEM approved replacement part for dryers. It can also be known as a bearing drum slide, pad, or glide. The slides attach to the inner most slots on the front beari...
In Stock
Order within the next 49 mins and your part ships today!
If the lightbulb inside your dryer drum has burned out, this is an authentic OEM replacement. It is a 10W, 120V bulb that is sold individually. The bulb turns on when the dryer door is open and should...
In Stock
Order within the next 49 mins and your part ships today!
$11.38
This part helps to keep the door closed while the machine is running.
In Stock
Order within the next 49 mins and your part ships today!
Sold individually.
In Stock
Order within the next 49 mins and your part ships today!
TThe door strike for your dryer is mounted on the dryer frame that the door shuts onto. It fits into the door catch on the door and keeps the door closed. If the door strike is damaged or missing, the...
In Stock
Order within the next 49 mins and your part ships today!
This is a replacement O-ring for the drum bearing retainer on your dryer. The drum bearing is found at the back of the dryer drum. The O-ring is designed to create a seal on the drum bearing. The O-r...
In Stock
Order within the next 49 mins and your part ships today!
$32.49
A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.
In Stock
Order within the next 49 mins and your part ships today!
This felt attaches to the top bearing.
In Stock
Order within the next 49 mins and your part ships today!
The adjustable leveling screws on the bottom of your dryer can be screwed in or out to lower or raise the leg level. If one of the leveling screws is stripped, damaged, or missing, you may not be able...
In Stock
Order within the next 49 mins and your part ships today!
NOTE: Be very careful to not handle the igniter by its gray part as it's very fragile. Hold it by its white tip only.
In Stock
Order within the next 49 mins and your part ships today!
This part is located on the housing for the heating element.
In Stock
Order within the next 49 mins and your part ships today!

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for DPVH880GJ2WW

Viewing 4 of 4
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Marks left on clothes
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door won’t close
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Not Heating
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Gary L. from Freeport, IL
Parts Used:
WE04X25996, WE4X448
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
The dryer drum turned ok, but the gas heat did not start.
First I found and watched three videos on how to open the dryer and replace the igniter.
Then I opened the dryer, but I did not remove the belt as suggested in the video, and then I removed the ignitor and flame detecter as the videos had shown.
I got on-line and ordered the new parts from PartsSelect in the afternoon and had t hem in my hands the next morning by 9:30 am.
I installed the new parts and everything worked fine again. You must be very careful with the igniter to not touch it with hands or anything else. I practiced puting in the old parts first.
114 of 154 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joshua from Dallas, TX
Parts Used:
WE4M415
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set
Dryer would not start
The end repair was very simple and took minimal effort. The time and difficulty was all in the testing. I disassembled the dryer and removed the drum and then hard wired each thermo-fuse to determine where the fault was. After test all of those I was stumped. When I opened the door the light would not come on so I assumed it was a pow er fault closer to the source. However after all of my testing I couldn't find anything wrong. I then removed the light bulb and realized it was burned out which led me to the door switch being the fault. I removed the switch and soldered the three wire together and the dryer started right up! All I had to do was order a new $15 part, unsolder the wires and plug them in. Would have been so much simpler if that light bulb hadn't of been burned out causing me to over think my diagnosis. This was my first major appliance repair and I did it with only the help of the parts diagram provided on the website.
88 of 130 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
robert from mount joy, PA
Parts Used:
WE1M1011, WE1X1192
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
dryer door wont stay shut
pulled out door striker anddoor latch out with pliers and just pushed in new parts. works like new in under a min.
80 of 118 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!