PTD90GBPT1RS General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lisha|Lamb from SHELDON, MO
- Parts Used:
- WE03X23881
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lint filter tore
Replaced riped filter with new mesh filter screen.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from San Antonio, FL
- Parts Used:
- WE11X29438
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench set
Deflector was covered in burnt something.
Deflector has 3 bolts attaching it. They require a star wrench. Had to purchase same to do the repair. Removed the bolts(they are sheet metal type screws(bolts). Installed the deflector and started dryer. Loud rubbing sound noted. Shut off and checked the drum and noted it was not running concentrically. Removed deflector and the found the 3 screws actually retained the drum to drive. Had to make alignment pins to allow proper alignment of the drive, drum, and deflector. Once the pins were used during installation of the deflector everything worked correctly. Turned on dryer and it operated normally.
Had I had the proper tools the repair would probably have taken 30 minutes or less.
Had I had the proper tools the repair would probably have taken 30 minutes or less.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Alexandria, VA
- Parts Used:
- WE11X29438
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Heat deflector was covered in melted plastic
Someone I'm related to by marriage accidentally dried a plastic-coated tablecloth on high heat, and our heat deflector was hosed. I was very happy to find this part here for such a reasonable price; Sears wanted about $65 for it. Installation required a Torx bit, and removing the old one was easy, but the dryer's design made it difficult to reinstall the heat deflector while keeping the dryer running concentrically. I ended up cutting the heads off three screws, threading those into the plate behind the drum, sliding the new heat deflector on over those, and then one by one replacing them with the original Torx head screws. Once I figured it out it didn't take long but it took me a while to figure it out. That's probably more a reflection on me than the dryer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cristina from WHITTIER, CA
- Parts Used:
- WE03X23881
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken/ Tore Lint Filter
Opened dryer door and pulled out and Removed Broken old Lint Filter, inserted New Lint Filter into Lint Filter slot, then closed Dryer door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARY from AUGUSTA, GA
- Parts Used:
- WE11X29438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dried something with a plastic coating-
Used an allen wrench to remove the heat deflector and used allen wrench to replace it with the new one. HINT!! Do not lean on the inside of the dryer!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margarita from AUSTIN, TX
- Parts Used:
- WE03X23881
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lint Filter Frayed
Took out frayed lint filter and put in new lint filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aaron from MERIDIAN, ID
- Parts Used:
- WE03X23881
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
needed new lint filter
pulled out old one put in new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from CANTON, OH
- Parts Used:
- WE03X23881
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old filter had holes in it
No repair, just replace the old with the new. Fast delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BREVARD, NC
- Parts Used:
- WE11X29438
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Heat deflecter coated with plastic from drying plastic table cloth.
Advice from others with same problem on your web site was very helpful. I removed one of the three torx screws holding the deflecter, Used 2.5 star-drive screw diver bit and cordless drill/driver. Replaced 2 of three torx screws holding the deflecter with the headless brass screws, Using vice grip to tighten. Removed third torx screw and removed old deflector. Used shop vac to clean behind it. Installed new deflector, sliding it over the 2 headless screws, then installing one of the torx screws, then replacing the brass screws with original torx screws, one at a time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from OKLAHOMA CITY, OK
- Parts Used:
- WE03X23881
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lent filter was worn out, the screen was ripped and torn from west.
Very simple and easy it took no more than 10 seconds if that long. Remove the worn out screen (pull up and out), replace it with the new screen( slide it into the area where the old screen was removed. (No tools needed)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth A from STEVENS POINT, WI
- Parts Used:
- WE03X23881
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Torn screen on lint filter
Just put new lint filter in slot
I had torn the screen on the original one
I had torn the screen on the original one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from SUN CITY WEST, AZ
- Parts Used:
- WE03X23881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Lint filter in the dryer was damaged from continuous use.
I just popped in the new Filter and it fit perfectly. This will prolong the dryer use, looks like new.
Thank you Part Select.
One Happy customer
Thank you Part Select.
One Happy customer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from NOVATO, CA
- Parts Used:
- WE01X25160
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed a shoe rack
Lift the lint filter and slide the 2 hooked ends into the 2 holes provided . Front end is locked in as other end is suspended .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerard from goldsboro, NC
- Parts Used:
- WE09X27634
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
the felt in front door worn out
i follow your video and all went well except now the dryer will not heat. i went back on your site an tried the no heat option an still no heat
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sydrell from CHICAGO, IL
- Parts Used:
- WE03X23881
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the bracket around the net was cracked
removed old lint trap cleaned excess lint that fell inside from the broken lint trap made it easier for new lint trap to slide in.
Was this instruction helpful to you?
Thank you for voting!