Models > DDG7900LA

DDG7900LA General Electric Dryer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
Idler Pulley Wheel – Part Number: WE12X81
$31.03
This white idler pulley is used for many clothes dryers. A dryer's idler pulley wheel serves to help the belt to rotate the drum.
In Stock
Drive Motor – Part Number: WE17X10010
$348.87
Replaces "T" and "V" style motors. Includes two motor pulleys. If you have an older model dryer, the pulley may be pressed on or held on with a set screw. If pulley is pressed on, a new motor pulley must be ordered.
In Stock
Door Switch – Part Number: WE4X197
This part has three terminals. Note: Use the two smaller terminals for models that only have two wires to the switch.
No Longer Available
THERMOSTAT – Part Number: WE4X592
No Longer Available
Multi Rib Belt – Part Number: WE12X36P
$24.23
This dryer drum belt has three ridges. The belt has been updated by the manufacture and is now thinner.
In Stock
DISCONTINUED – Part Number: WE4X198
No Longer Available
DISCONTINUED – Part Number: WE4X668
No Longer Available
DISCONTINUED – Part Number: WE12X35
$50.77
Special Order
DISCONTINUED – Part Number: WE4X336
No Longer Available
DISCONTINUED – Part Number: WE4X582
No Longer Available

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for DDG7900LA

Viewing 1 of 1
Noisy
Fixed by these parts
Fixing Fixing
How to fix it
Replacing the Drive Motor

Replacing the Drive Motor

View More
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Robert from Virginia Beach, VA
Parts Used:
WE4X197
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
replqce bad switch
pried old switch assembly from front of machine with screw driver. removed 2 electrical connections. shorted terminals to verify problem. inserted wiring terminals to new switch. verified operation and then pushed switch assembly into machine opening.
30 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sam from Durham, PA
Parts Used:
WE12X81
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Dryer became very noisy
--Removed bottom rear panel (right under where 220 line comes in) which exposed belt and idler pulley.
--Relieved tension on belt by moving idler arm and moved belt off idler puller (just to the side).
--Removed e-clip.
--Removed old pulley and washers.
--Installed new thick plastic washer first, then pulley, then e-cl ip.
--Relieve tension and place belt back on new pulley.
--Replace back panel.
-Fini!
Read less
13 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Santa Barbara, CA
Parts Used:
WE4X197
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Dryer would not start
I checked the power (OK) and removed the four screws that held the timer/controls (upper panels) cover. This revealed a schematic for the dryer that enabled me to determine the door swich was probably the culprit. I pried out the old switch and, sure enough, it was always open (checked with multi-meter). I found the replacement switch eas ily using the dryer model number and "door switch" search string. Ordered Sunday night, the part came on Tuesday and took 2 minutes to install (no tools needed).
Read less
8 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More