CFRE1001PW0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bruce from Seminole, FL
- Parts Used:
- 5303207102, 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door Latch & Door Strike Broken On Dryer
I removed the broken door latch & strike with pliers. Then I pushed the new parts into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Dallas, TX
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My husband ruined the old latch by trying to shut the door too hard, and the old latch fell down into the inside of the dryer.
I took the new latch out of the package and snapped it into place. It took about 15 seconds, and that included the walk to the laundry room!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from RUIDOSO, NM
- Parts Used:
- 134587700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer cut off before the clothes were dry.
All the symptoms indicated the thermister (located in the exhaust air stream of the dryer) was the problem. Pulled the lower panel off the dryer. Took out the two lower screws holding the door panel on so I could pull the front panel out just enough to get a screwdriver on the screws holding the thermister on. Unhooked the two wires connected to it and hooked them to the new thermister(no need to observe polarity). Put the new thermister in, screwed the door panel back down, put the lower panel on and started drying clothes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from PFLUGERVILLE, TX
- Parts Used:
- 134719300
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Drum belt broke
I removed the front, top and back panels of the dryer, installed belt around drum and through the pulley system so the belt was snug, replaced all screws and panels, and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Saint Augustine, FL
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer door part broke
Dryer door would not close, part had broke and fallen in. Once part was received it took less than an minute to put the new one in and I was back in business.
thanks for making it easy to find the part needed. and the delivery was fast!
bonnie J.
thanks for making it easy to find the part needed. and the delivery was fast!
bonnie J.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Martinsville, IN
- Parts Used:
- 5303207102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken Door Strike
After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.
I also noted that the new part was of a better design than the original. It should not need further attention.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWARD W from LA CENTER, WA
- Parts Used:
- 137553402
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket became unattached from the dryer door
Very easy lined the slots on the dryer door with the gasket and
pushed the small tabs into the slots of the gasket door with my
fingers - A $10 fix that would have probably would have been in
excess of $100 if we called a service repair person
pushed the small tabs into the slots of the gasket door with my
fingers - A $10 fix that would have probably would have been in
excess of $100 if we called a service repair person
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- karen from aurora, IL
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer door wouldnt close
the catch on the door was worn and cracked.... so I noticed it could be easily popped out with a screw driver and when the new part came in the mail 2 days later, it was just as easy to pop back in with no tools required. Now the door stays shut really good!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from DULUTH, MN
- Parts Used:
- 137553402
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door seal/gasket coming off of dryer door. Could not make it stay as designed.
This was the easiest repair ever done. Pulled out old seal/gasket and popped in new one. Took about 2 minutes. Be sure to mark where ends of new door seal (gasket) starts and ends when removing the old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from St. Peters, MO
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
female part of door clasp broke
All I did was push the new part into the machine! So easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from HUDSON, NY
- Parts Used:
- 3204267
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
dryer stopped in middle of cycle and would not restart
followed the repair video and replaced thermal fuse and thermostat(recommend replacing both due to the problem could of resulted in either part being the cause),Repair went relatively easy.I also recommend to clean and vacuum the dryer while you have it all apart due to a lot of lint buildup and don't forget to unplug before servicing!Stay Safe!!!
Was this instruction helpful to you?
Thank you for voting!
door catch wasn't working and screws in door were loose.
popped the catch in existing hole and replaced the screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- keith from ELLENVILLE, NY
- Parts Used:
- 3204267
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Cloths not drying
Removed the back panel and the exhaust hose.removed the heater element and changed the thermostat wire was melted cut damaged part of wire soldered and rapped with black electrical tap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from CHALMETTE, LA
- Parts Used:
- 137553402
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old gasket became worn, no longer would hold in place, taking longer to dry
EZ. Viewed you tube replacement video, EZ off and on, applied little heat, closed dryer door, good fit, heat made it fit even better
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ROUND TOP, NY
- Parts Used:
- 3204267
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
The thermostat had deteriorated and no heat
Had to loosen drum and move it forward to get at switch. Didn’t have to remove belt.
Was this instruction helpful to you?
Thank you for voting!