CFSE5115PA1 Frigidaire Dryer - Instructions

When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replacing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)

All the symptoms indicated the thermister (located in the exhaust air stream of the dryer) was the problem. Pulled the lower panel off the dryer. Took out the two lower screws holding the door panel on so I could pull the front panel out just enough to get a screwdriver on the screws holding the thermister on. Unhooked the two wires connected to it and hooked them to the new thermister(no need to observe polarity). Put the new thermister in, screwed the door panel back down, put the lower panel on and started drying clothes.

By undoing the single screw which holds the sensor in place, the old one falls off. To replace: simply pop the two wires on their connections (small metal studs on the back), slide clip/wire end of sensor in place and replace the screw. You are back in business! Very simple repair that a DIY can save a ton!

1. Loosened the 3 screws inside of the drum
2. Removed the entire back of the dryer (lots of screws)
3. Removed the old vent (there are 2 screws at the bottom that hold it in)
4. Install new vent (put the screws back in)
5. Close up back and proceed to put all of the screws back

Unpluged the dryer, took out the light assembly, unpluged the wires to the unit, replaced the old unit with new unit from Partselect.
Plugged dryer in, problem fixed.
Taa Daa

Thanks, PARTSELECT.

That saved me about $50.00 YAHOO!!

After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.

Removed the back panel and the exhaust hose.removed the heater element and changed the thermostat wire was melted cut damaged part of wire soldered and rapped with black electrical tap

This was the easiest repair ever done. Pulled out old seal/gasket and popped in new one. Took about 2 minutes. Be sure to mark where ends of new door seal (gasket) starts and ends when removing the old one.

Very easy lined the slots on the dryer door with the gasket and
pushed the small tabs into the slots of the gasket door with my
fingers - A $10 fix that would have probably would have been in
excess of $100 if we called a service repair person

EZ. Viewed you tube replacement video, EZ off and on, applied little heat, closed dryer door, good fit, heat made it fit even better

Removed screw and disconnect wires. Connect wires to new Moisture Sensor and slide clip to right side of dryer and tighten screw on left side.

Had to loosen drum and move it forward to get at switch. Didn’t have to remove belt.

Watched a YouTube video. Very easy to replace, I’m 73 year old woman…this was a very easy job, anyone can do it!

followed the repair video and replaced thermal fuse and thermostat(recommend replacing both due to the problem could of resulted in either part being the cause),Repair went relatively easy.I also recommend to clean and vacuum the dryer while you have it all apart due to a lot of lint buildup and don't forget to unplug before servicing!Stay Safe!!!

popped the catch in existing hole and replaced the screws