Models
>
GLGR331CAS0
GLGR331CAS0 Frigidaire Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for GLGR331CAS0
Viewing 5 of 5
Keep searches simple, eg. "belt" or "pump".
$17.44
The drum belt, also known as a drive belt, is a rubber piece that wraps around the dryer drum, idler pulley, and motor pulley and is used to make the drum rotate. If you can hear the motor running, bu...
In Stock
Order now and your part arrives by May 3
$56.24
This selector knob is a genuine OEM replacement part for either your washer or your dryer. The knob is used to select the cycle desired for your laundry. If the knob has become cracked or damaged it w...
In Stock
Order now and your part arrives by May 3
$10.88
The drum support bearing is an authentic OEM replacement part for your dryer. The bearing is used to support the drum and allow it to rotate smoothly and quietly. If your dryer is excessively noisy wh...
In Stock
Order now and your part arrives by May 3
$64.74
This part is used to start the dryer once you have selected a setting on the timer.
In Stock
Order now and your part arrives by May 3
$27.28
This coil ignition kit is used in dryers to open the gas valve when the dryer is on. This kit includes two coils. One is a two-wire secondary coil and the other is a three-wire booster coil. If your d...
In Stock
Order now and your part arrives by May 3
On Order
$22.91
This drum bearing bracket is for dryers. Drum bearing bracket holds and supports the drum bearing
In Stock
Order now and your part arrives by May 3
$32.12
This white dryer lint filter screen collects lint as it passes through the dryer vent.
In Stock
Order now and your part arrives by May 3
$59.35
Part may differ in color from image. Please note that this is only a cosmetic difference.
In Stock
Order now and your part arrives by May 3
$24.00
This screw is designed to fit washers and dryers. Refer to the diagram provided by the manufacturer for further installation instructions and accurate application of screw in your tool.
In Stock
Order now and your part arrives by May 3
$53.58
This part is the replacement door handle for your dryer. It is made of white plastic and measures about 2 ½ inches long and 4 inches wide. The door handle allows you to open and close the dryer door. ...
In Stock
Order now and your part arrives by May 3
$25.10
This is a screw and it is used with a variety of home appliances. It is less than 1/2 an inch long, and is #8-18 x 3/8. This part is a pan head, sheet metal, screw. It is made of metal.
In Stock
Order now and your part arrives by May 3
Common Problems and Symptoms for GLGR331CAS0
Viewing 8 of 8Noisy
Fixed by these parts
How to fix it
Drum Not Spinning
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Not Heating
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Too hot
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Knob replacement
Just slipped them on and ready to go. Ordered them on thur and got em on Tues.
Was this instruction helpful to you?
Thank you for voting!
dryer start switch shaft was broken by using pliers after knob was lost
I first disconnected the power by unplugging power cord.
I then removed back cover from control panel using philips screwdriver.
I removed the start switch by twisting it counter clockwise.
I removed the two push on connectors from the start switch.
I installed the two connectors on the new swi ... Read more tch.
I twisted the new switch into place, and installed the new knob.
I reinstalled the back cover plate.
I inserted the power cord back into the receptacle.
I twisted the start knob clockwise.
VOILA!!!!!
I then removed back cover from control panel using philips screwdriver.
I removed the start switch by twisting it counter clockwise.
I removed the two push on connectors from the start switch.
I installed the two connectors on the new swi ... Read more tch.
I twisted the new switch into place, and installed the new knob.
I reinstalled the back cover plate.
I inserted the power cord back into the receptacle.
I twisted the start knob clockwise.
VOILA!!!!!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brett from Monticello, MN
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer would heat initially then cool down
The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils we
... Read more
re easily accessible on the bottom left side. A metal bracket held the coils on and was somewhat tough to get the two screws removed on it as they were stuck, but once they were removed the coils easily came out and I was able to replace them in minutes. The whole job took 15-20 minutes and I now have a dryer that heats through the entire drying cycle.
Read less
Was this instruction helpful to you?
Thank you for voting!