Models
>
EFMC627UIW2
EFMC627UIW2 Frigidaire Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for EFMC627UIW2
Viewing 5 of 5
Keep searches simple, eg. "belt" or "pump".
$56.28
The two-terminal high limit thermostat has a limit of 260 degrees Fahrenheit and acts as a safety mechanism that keeps the dryer from overheating. The thermostat will cut out when the internal dryer t...
In Stock
Order now and your part arrives by Oct 29
$25.25
This screw is designed to fit washers and dryers. Refer to the diagram provided by the manufacturer for further installation instructions and accurate application of screw in your tool.
In Stock
Order now and your part arrives by Oct 29
$30.95
Keep your dryer operating properly with this dryer belt, designed to rotate the drum during each cycle for effective drying. Made from durable material, it provides the strength needed to handle regul...
In Stock
Order now and your part arrives by Oct 29
$26.35
This is a screw and it is used with a variety of home appliances. It is less than 1/2 an inch long, and is #8-18 x 3/8. This part is a pan head, sheet metal, screw. It is made of metal.
In Stock
Order now and your part arrives by Oct 29
In Stock
Order now and your part arrives by Oct 29
In Stock
Order now and your part arrives by Oct 29
In Stock
Order now and your part arrives by Oct 29
$39.46
This dryer thermal fuse is a critical safety component designed to protect the appliance from overheating. It automatically shuts off power to the motor or heating system if excessive temperatures are...
In Stock
Order now and your part arrives by Oct 29
$89.81
This element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is u...
In Stock
Order now and your part arrives by Oct 29
$222.77
This dryer motor powers both the drum and the blower wheel. It includes a pulley for the drum belt and uses reverse threads to secure the blower wheel. For safety, disconnect power before installation...
In Stock
Order now and your part arrives by Oct 29
In Stock
Order now and your part arrives by Oct 29
$54.95
This dryer idler arm spring maintains proper tension on the drive belt, helping keep the drum rotating smoothly during operation. By ensuring the belt stays secure and properly aligned, it supports ef...
In Stock
Order now and your part arrives by Oct 29
Common Problems and Symptoms for EFMC627UIW2
Viewing 6 of 6Noisy
Fixed by these parts
How to fix it
Drum Not Spinning
Fixed by these parts
How to fix it
Not Heating
Fixed by these parts
How to fix it
Too hot
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from PFLUGERVILLE, TX
- Parts Used:
- 134719300
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Drum belt broke
I removed the front, top and back panels of the dryer, installed belt around drum and through the pulley system so the belt was snug, replaced all screws and panels, and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from HUDSON, NY
- Parts Used:
- 3204267
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
dryer stopped in middle of cycle and would not restart
followed the repair video and replaced thermal fuse and thermostat(recommend replacing both due to the problem could of resulted in either part being the cause),Repair went relatively easy.I also recommend to clean and vacuum the dryer while you have it all apart due to a lot of lint buildup and don't forget to unplug before servicing!Sta
... Read more
y Safe!!!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from PENSACOLA, FL
- Parts Used:
- 5304533199
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Dryer would not start, no interior light, no indicator lights
Watched several videos on unit disassembly/reassembly and fault repair (YouTube is great). Moved the dryer into the garage. Removed the top cover, front loading door assembly and back panel. I used a large piece of cardboard as my screw holder. As I removed a screw, I drilled it into the cardboard and then wrote what they were for and how
... Read more
many there were (some of the notes were very specific). Visual inspection revealed the relay on the main control board (MCB) had failed (burnt up and spewed molten plastic on several of the MCB's wiring harnesses and wiring connectors). The failed relay had melted and pitted the wires and connectors for the heater (they needed to be replaced). Purchased a new MCB (it came with a complete wiring harness). Vacuumed all of the dryer components. Took photos of everything I replaced/touched (the MCB, wiring harness routing, location of the wiring harness clips, assembly screws, wires to each component). Unmounted the old MCB and disconnected the wiring harness clips for the harness going to the front door assembly. Mounted the new MCB and inserted the new wiring harness clips (for the front section). One wire at a time, removed the old wiring harness connector and installed the new wiring harness connector, in its place. Once the front was completed, moved to the wiring harness going to the back and underneath of the dryer. Followed the same steps and methodically replaced the wiring harness. Reattached the back panel, front loading door assembly and the top cover. Re-installed the dryer in the laundry room made the wall connections and tested it. It works!!!
Read less
Was this instruction helpful to you?
Thank you for voting!