Models
>
EFMC627UIW0
EFMC627UIW0 Frigidaire Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for EFMC627UIW0
Viewing 6 of 6
Keep searches simple, eg. "belt" or "pump".
$56.28
The two-terminal high limit thermostat has a limit of 260 degrees Fahrenheit and acts as a safety mechanism that keeps the dryer from overheating. The thermostat will cut out when the internal dryer t...
In Stock
Order now and your part arrives by Oct 29
$25.25
This screw is designed to fit washers and dryers. Refer to the diagram provided by the manufacturer for further installation instructions and accurate application of screw in your tool.
In Stock
Order now and your part arrives by Oct 29
$30.95
Keep your dryer operating properly with this dryer belt, designed to rotate the drum during each cycle for effective drying. Made from durable material, it provides the strength needed to handle regul...
In Stock
Order now and your part arrives by Oct 29
$26.35
This is a screw and it is used with a variety of home appliances. It is less than 1/2 an inch long, and is #8-18 x 3/8. This part is a pan head, sheet metal, screw. It is made of metal.
In Stock
Order now and your part arrives by Oct 29
In Stock
Order now and your part arrives by Oct 29
In Stock
Order now and your part arrives by Oct 29
In Stock
Order now and your part arrives by Oct 29
$39.46
This dryer thermal fuse is a critical safety component designed to protect the appliance from overheating. It automatically shuts off power to the motor or heating system if excessive temperatures are...
In Stock
Order now and your part arrives by Oct 29
$89.81
This element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is u...
In Stock
Order now and your part arrives by Oct 29
$222.77
This dryer motor powers both the drum and the blower wheel. It includes a pulley for the drum belt and uses reverse threads to secure the blower wheel. For safety, disconnect power before installation...
In Stock
Order now and your part arrives by Oct 29
In Stock
Order now and your part arrives by Oct 29
$54.95
This dryer idler arm spring maintains proper tension on the drive belt, helping keep the drum rotating smoothly during operation. By ensuring the belt stays secure and properly aligned, it supports ef...
In Stock
Order now and your part arrives by Oct 29
Common Problems and Symptoms for EFMC627UIW0
Viewing 6 of 6Noisy
Fixed by these parts
How to fix it
Drum Not Spinning
Fixed by these parts
How to fix it
Not Heating
Fixed by these parts
How to fix it
Too hot
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from PFLUGERVILLE, TX
- Parts Used:
- 134719300
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Drum belt broke
I removed the front, top and back panels of the dryer, installed belt around drum and through the pulley system so the belt was snug, replaced all screws and panels, and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from HUDSON, NY
- Parts Used:
- 3204267
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
dryer stopped in middle of cycle and would not restart
followed the repair video and replaced thermal fuse and thermostat(recommend replacing both due to the problem could of resulted in either part being the cause),Repair went relatively easy.I also recommend to clean and vacuum the dryer while you have it all apart due to a lot of lint buildup and don't forget to unplug before servicing!Sta
... Read more
y Safe!!!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- keith from ELLENVILLE, NY
- Parts Used:
- 3204267
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Cloths not drying
Removed the back panel and the exhaust hose.removed the heater element and changed the thermostat wire was melted cut damaged part of wire soldered and rapped with black electrical tap
Was this instruction helpful to you?
Thank you for voting!