Models > EFDG317TIW0

EFDG317TIW0 Electrolux Dryer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for EFDG317TIW0

Viewing 6 of 6

Manuals & Guides for EFDG317TIW0

Click to download
Keep searches simple, eg. "belt" or "pump".
This coil ignition kit is used in dryers to open the gas valve when the dryer is on. This kit includes two coils. One is a two-wire secondary coil and the other is a three-wire booster coil. If your d...
In Stock
Order within the next 11 hrs and your part ships today!
$11.21
This screw is designed to fit washers and dryers. Refer to the diagram provided by the manufacturer for further installation instructions and accurate application of screw in your tool.
In Stock
Order within the next 11 hrs and your part ships today!
$11.75
This is a screw and it is used with a variety of home appliances. It is less than 1/2 an inch long, and is #8-18 x 3/8. This part is a pan head, sheet metal, screw. It is made of metal.
In Stock
Order within the next 11 hrs and your part ships today!
This part senses the flame for heat allowing the gas valve to open.
In Stock
Order within the next 11 hrs and your part ships today!
$70.59
This lint screen is for dryers. The lint screen traps lint and debris from the exhaust air flowing from the dryer.
In Stock
Order within the next 11 hrs and your part ships today!
$62.82
INCLUDES 5304523151 SHAFT, 5304523152 ROLLER, 5304523153 NUT, 5304523154 SPACER.
In Stock
Order within the next 11 hrs and your part ships today!
$57.93
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
$89.91
In Stock
Order within the next 11 hrs and your part ships today!
$193.95
This dryer drum drive motor with pulley for drum belt has reverse threads for the blower wheel. This is a genuine OEM part.
In Stock
Order within the next 11 hrs and your part ships today!
$42.81
This switch is for a dryer door without a drum light.
In Stock
Order within the next 11 hrs and your part ships today!

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for EFDG317TIW0

Viewing 3 of 3
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Marks left on clothes
Fixed by these parts
Fixing Fixing
How to fix it
Drum Not Spinning
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Brett from Monticello, MN
Parts Used:
5303931775
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Dryer would heat initially then cool down
The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils we re easily accessible on the bottom left side. A metal bracket held the coils on and was somewhat tough to get the two screws removed on it as they were stuck, but once they were removed the coils easily came out and I was able to replace them in minutes. The whole job took 15-20 minutes and I now have a dryer that heats through the entire drying cycle.
95 of 108 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bruce from Burnsville, MN
Parts Used:
5303931775
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Dryer would heat only on the initial start. Burner would not light again until completely cooled down. The ignitor would energize, but no gas would flow for ignition.
1. Pry Dryer top up and off the clips. (Front of Dryer)
2. Remove 2 phillips screws on the inside of front panel.
3. Lift front panel up and set off to the side
4. Removed 2 phillips screws with short handled phillips driver that hold the gas valve coil bracket in place.
5. Unplugged and removed both coils, install ed new coils and bracket. Re installed front panel, screws and top.
40 of 47 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Philip from Oakland, CA
Parts Used:
134719300, 5304523155
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
Noisy Dryer
When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replac ing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)
37 of 45 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!