Models
>
EIMED6CLSS4
EIMED6CLSS4 Electrolux Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for EIMED6CLSS4
Viewing 6 of 6
Manuals & Guides for EIMED6CLSS4
Click to downloadInstall
Installation Instructions
(2.42MB)
Specs
Product Specifications Sheet
(0.6MB)
Wiring
Wiring Diagram
(0.6MB)
Keep searches simple, eg. "belt" or "pump".
$56.28
The two-terminal high limit thermostat has a limit of 260 degrees Fahrenheit and acts as a safety mechanism that keeps the dryer from overheating. The thermostat will cut out when the internal dryer t...
In Stock
Order now and your part arrives by Nov 19
This is an adjustable foot for your freezer, refrigerator, and dryer. This part supports your unit by screwing into one of the bottom four corners, and adjusting the height of your machine. If your ap...
In Stock
Order now and your part arrives by Nov 19
$25.25
This screw is designed to fit washers and dryers. Refer to the diagram provided by the manufacturer for further installation instructions and accurate application of screw in your tool.
In Stock
Order now and your part arrives by Nov 19
$30.95
Keep your dryer operating properly with this dryer belt, designed to rotate the drum during each cycle for effective drying. Made from durable material, it provides the strength needed to handle regul...
In Stock
Order now and your part arrives by Nov 19
$26.35
This is a screw and it is used with a variety of home appliances. It is less than 1/2 an inch long, and is #8-18 x 3/8. This part is a pan head, sheet metal, screw. It is made of metal.
In Stock
Order now and your part arrives by Nov 19
In Stock
Order now and your part arrives by Nov 19
In Stock
Order now and your part arrives by Nov 19
$39.46
This dryer thermal fuse is a critical safety component designed to protect the appliance from overheating. It automatically shuts off power to the motor or heating system if excessive temperatures are...
In Stock
Order now and your part arrives by Nov 19
$84.23
This moisture sensor assembly ensures your dryer delivers optimal performance by detecting the moisture level in each load. By accurately measuring dampness, it allows the appliance to adjust cycle ti...
In Stock
Order now and your part arrives by Nov 19
$89.81
This element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is u...
In Stock
Order now and your part arrives by Nov 19
$17.55
This part is the replacement screw for your washer. The head is approximately inch in diameter and the screw is approximately 3/4 inch in length. It is made of metal and is sold individually. This is...
In Stock
Order now and your part arrives by Nov 19
$222.77
This dryer motor powers both the drum and the blower wheel. It includes a pulley for the drum belt and uses reverse threads to secure the blower wheel. For safety, disconnect power before installation...
In Stock
Order now and your part arrives by Nov 19
Common Problems and Symptoms for EIMED6CLSS4
Viewing 7 of 7Noisy
Fixed by these parts
How to fix it
Drum Not Spinning
Fixed by these parts
How to fix it
Not Heating
Fixed by these parts
How to fix it
Too hot
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stacey from TWO RIVERS, WI
- Parts Used:
- 134786100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The clip broke off our sensor making it disconnect, thus we had in inoperable 'new' machine.
By undoing the single screw which holds the sensor in place, the old one falls off. To replace: simply pop the two wires on their connections (small metal studs on the back), slide clip/wire end of sensor in place and replace the screw. You are back in business! Very simple repair that a DIY can save a ton!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from PFLUGERVILLE, TX
- Parts Used:
- 134719300
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Drum belt broke
I removed the front, top and back panels of the dryer, installed belt around drum and through the pulley system so the belt was snug, replaced all screws and panels, and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from HUDSON, NY
- Parts Used:
- 3204267
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
dryer stopped in middle of cycle and would not restart
followed the repair video and replaced thermal fuse and thermostat(recommend replacing both due to the problem could of resulted in either part being the cause),Repair went relatively easy.I also recommend to clean and vacuum the dryer while you have it all apart due to a lot of lint buildup and don't forget to unplug before servicing!Sta
... Read more
y Safe!!!
Read less
Was this instruction helpful to you?
Thank you for voting!