Models > ALE331RAW

ALE331RAW (PALE331RAW) Amana Dryer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for ALE331RAW

Viewing 7 of 7
Keep searches simple, eg. "belt" or "pump".
If your dryer is not tumbling, takes a long time to dry, or is noisy while tumbling, it may be time to replace the drum support rollers. These hold the drum in place while it rotates, so if they have ...
In Stock
Order within the next 6 hrs and your part ships today!
The multi rib belt, which may also be called a dryer drum belt or a multi-v belt, helps to rotate the drum of the dryer. The belt wraps completely around the drum, around a tension pulley, and then ar...
In Stock
Order within the next 6 hrs and your part ships today!
$14.16
Located in the front bulkhead of your dryer are two drum glides, which help to ensure that the drum rotates smoothly and quietly while the dryer is operating. When the glides wear down, it can cause a...
In Stock
Order within the next 6 hrs and your part ships today!
$73.35
Note: This part no longer comes with the felt seal. This filter collects lint as it passes through the dryer vent.
In Stock
Order within the next 6 hrs and your part ships today!
This two inch wide idler pulley wheel is beige in color and is made of plastic. This pulley wheel comes with its own metallic bearing in its center.
In Stock
Order within the next 6 hrs and your part ships today!
This washer is 3/4 inches in diameter.
In Stock
Order within the next 6 hrs and your part ships today!
Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you do...
In Stock
Order within the next 6 hrs and your part ships today!
This kit comes in two pieces: the catch and the clip.
In Stock
Order within the next 6 hrs and your part ships today!
The spring for this part is sold separately. This idler assembly is for dryers. Idler assembly includes the idler arm and the idler pulley that maintains tension on the drive belt, allowing the ...
In Stock
Order within the next 6 hrs and your part ships today!
This metal retaining ring is well under an inch long. Use it for your Maytag brand clothes washer or your clothes dryer.
In Stock
Order within the next 6 hrs and your part ships today!
This part replaces older two terminal switches.
In Stock
Order within the next 6 hrs and your part ships today!
This part is located between the back of the drum and the rear dryer panel.
In Stock
Order within the next 6 hrs and your part ships today!

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for ALE331RAW

Viewing 9 of 9
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door won’t close
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Too hot
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Marks left on clothes
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Drum Not Spinning
Fixed by these parts
Fixing Fixing
How to fix it
Will not agitate
Fixed by these parts
Fixing Fixing
How to fix it
Burning smell
Fixed by these parts
Fixing Fixing
How to fix it
Won’t Start
Fixed by these parts
Fixing
How to fix it
Spins slowly
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Chris from Hopedale, MA
Parts Used:
WP37001042, WP233520
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Drum not centered , clothes getting stuck in dryer
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared of f. I took the new drum support roller out and carefully slid it over the shaft, I had to jiggle it around for a bit, but then it finally was seated correctly. I replaced the washer and then the clip using a pair of needle nose pliers and a regular screw driver and then turned the dryer by hand to see if the wheel came off. After confirming that it worked, I put the cover back on, and plugged it in and tested it.
523 of 546 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tim from South Glens Falls, NY
Parts Used:
37001141, WP37001132, WP37001142
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
The Felt Gasket between drum and door ripped, vent manifold from Dryer to fan and lint screen broken
I pulled the bottom panel and the door panel to replace the manifold and felt gasket around the drum. I removed old gasket very easily, it peeled right off. I use brake cleaning fluid (Spray Can from Auto Zone about $1.45) to remove old glue. Used spray contact cement (Elmer's about 4.50 at Ace) and sprayed the panel and gasket surface s and let dry. I then applied a 2nd coat and let get "tacky" and installed the gasket. You will need an extra set of hands to hold the gasket in place while you stretch it over the the panel. The vent manifold is held in place with 3 phillips screws and was installed in about 10 minutes. The only gripe I had was in the Parts-Select illustrated breakdown they don't tell you the lint screen comes with the manifold assembly, so I bought one of them too. Now have an extra lint screen
498 of 504 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mirsada from Yorktown Heights, NY
Parts Used:
WP37001142
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Filter Lint Was Broken
Took it out of the box and put it in the dryer. I could not find this part anywhere else but on this website. The item was delivered the next day to my surprise.
378 of 381 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!