WDF520PADB3 Whirlpool Dishwasher - Instructions

Step 1: Remove the screws in the bottom of the countertop.

Step 2: Remove the screws holding the bottom kickplate.

Step 3: Loosen leveling legs.

Step 4: Pull dishwasher out of hole.

Step 5: Unlplug dishwasher.

Step 6: Disconnect wires from bottom of element in back.

Step 7: Remove plastic nuts holding element in place.

Step 8: Remove element.

Step 9: Reverse Steps 1-7.

Step 10: Drink beer.

I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!

Pulled the dishwasher out from the counter, on the lower right hand side, about mid way back there is a bundle of all yellow wires, follow that to the sensor which mounts into the bottom of the wash tub. The sensor is easily removed by grasping it by hand and turn it about a half turn (can't remember which direction). It then just pulls out. Disconnect the wire bundle by pushing on the retaining clip and the install is the reverse.

My filters had completely clogged up and had not cleaned my filters at all which was a no-no.I had lots of food left on the dishes after running my dishwasher, so I took bothp filters out and replaced them no tools required. I won’t be using powdered or liquid detergent for my dishwasher anymore only pods and promise to clean my filters once a month, so hopefully that’ll help keep them clean. Very easy replacement even for an old woman.

unscrewed dishwasher from cabinet ...,moved out slightly....while door closed ...reached with long nosed pliers door spring pulled forward...and allowing white plastic part that fits through sleeve and fit new sleeve over it...pulled spring attaching white plastic part and pushed unit back to cabinet and replaced screws DONE.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I shut off the power to the dishwasher, then I removed the front panel under the door. On the right side just behind the electrical box there are two wires going up to the hi-limit thermostat, (you may need a small mirror to see it), remove one screw that is holding the thermostat bracket, unplug the wires from the old thermostat and install new one. Screw bracket and thermostat back to the underside of the dishwasher, reinstall the front panel, turn on the power, done.

I couldn't get dealer to order part, so went on line to see what was available. Found model and picture of part needed and ordered. It came in 3 days. Took part out of box and compared to part the needed replacing. It was a match. Removed old basket and replaced with new one. It works great and siverware stays in basket until put away.

Replaced the dish rack.

Removed the retaining clips on the front of the rail and removed the old rack.

Removed the spray arm assembly from the old rack.

Assembled the new rack, with the supplied parts from the kit. Using the old rack to know where some parts needed to be placed.

Put the spray arm assembly on the new rack.

Inserted the new rack into the rails

Replaced retaining clips.

Put thread tape on threads. Screwed water hose to part. Pushed hose onto part. Pushed electric clip to part. Screwed part onto washer. Done

bought a new one and put it in machine.

Removed old gasket. Cleaned the area and let dry. Aligned gasket, pressed into the groove. Corners are tricky, stretch and press to get a tight seal. Follow around appliance. Inital try, small leak. Adjusted seal second use no leak. 10/10 would recommend this part. Super easy self install.

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

Make sure you order 2. One on each side

I purchased this misguided by the official response to "Doug" on April 17, 2018, which at the time was labeled as "most helpful". This is NOT the little grommet in the center. This is a big grommet that goes no the supply pump. This is #14 in the diagram. (#15 is actually the clamp that holds it). If you are looking for the little grommet that goes on that stem on the central recirculation pump, that part is not available, it only comes fused on the sump, and for replacing the sump you have to disassemble the whole bottom part of the dishwasher, pumps, sensors, valves, hose...even this big grommet. A lot of work, and since you are at it, you might want to replace both grommets. If you need THIS big grommet (#14) only, then it is not so much work, just take out one clamp, one connected cable, and the grommet to replace. But check if your machine has reusable clamps, because if not, you might want to order a new clamp. Good luck!