7WDT770PAYM4 Whirlpool Dishwasher - Instructions

Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.

First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.

Step 1: Remove the screws in the bottom of the countertop.

Step 2: Remove the screws holding the bottom kickplate.

Step 3: Loosen leveling legs.

Step 4: Pull dishwasher out of hole.

Step 5: Unlplug dishwasher.

Step 6: Disconnect wires from bottom of element in back.

Step 7: Remove plastic nuts holding element in place.

Step 8: Remove element.

Step 9: Reverse Steps 1-7.

Step 10: Drink beer.

The unit had power, but the controls would not work. The "clean" light was blinking. I first replaced the control unit, no help. I then used the "just ask" and was told the problem was the heating element and/or the hi-temp thermostat. I replaced both those and used the re-set code pushing the "hi-temp/air dry, hi-temp/air dry" buttons. That did it. Easy parts to locate and replace. It took longer pulling the unit out and putting it back than it did to replace the parts.

Opened door and installed cap. Not much effort. But really got good service from Parts Select. Received order much faster than I had expected.

I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!

Pulled the dishwasher out from the counter, on the lower right hand side, about mid way back there is a bundle of all yellow wires, follow that to the sensor which mounts into the bottom of the wash tub. The sensor is easily removed by grasping it by hand and turn it about a half turn (can't remember which direction). It then just pulls out. Disconnect the wire bundle by pushing on the retaining clip and the install is the reverse.

After shutting off electricity, lay dishwasher on it's side (use a towel to absorb any water) then just use nut driver to remove faulty valve.

My filters had completely clogged up and had not cleaned my filters at all which was a no-no.I had lots of food left on the dishes after running my dishwasher, so I took bothp filters out and replaced them no tools required. I won’t be using powdered or liquid detergent for my dishwasher anymore only pods and promise to clean my filters once a month, so hopefully that’ll help keep them clean. Very easy replacement even for an old woman.

unscrewed dishwasher from cabinet ...,moved out slightly....while door closed ...reached with long nosed pliers door spring pulled forward...and allowing white plastic part that fits through sleeve and fit new sleeve over it...pulled spring attaching white plastic part and pushed unit back to cabinet and replaced screws DONE.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

1. Disconnect power at the breaker, 2. remove two wood screws fastening the dishwasher to the cabinet and slide the unit out approximately 2 inches. 3. Remove old latch strike and replace with redesigned strike. 4. Slide unit in and reattached to cabinet. 5. Remove 11 screws holding inner panel of door assembly and one screw holding user interface unit to door. 6. Disconnect snap cable to latch assembly and replace the latch unit. 7. Reassemble.

Sears could not supply us with the replacement cap for the dishwasher. We were saved by being able to get the cap here on your web page.Your web sight is like going into the garage and finding the part you saved up for many years that you knew you would need down the road.

I shut off the power to the dishwasher, then I removed the front panel under the door. On the right side just behind the electrical box there are two wires going up to the hi-limit thermostat, (you may need a small mirror to see it), remove one screw that is holding the thermostat bracket, unplug the wires from the old thermostat and install new one. Screw bracket and thermostat back to the underside of the dishwasher, reinstall the front panel, turn on the power, done.

I couldn't get dealer to order part, so went on line to see what was available. Found model and picture of part needed and ordered. It came in 3 days. Took part out of box and compared to part the needed replacing. It was a match. Removed old basket and replaced with new one. It works great and siverware stays in basket until put away.

Unplug the dishwasher,take the screws out of the coutertop,then slide dishwasher out turn it on its side. Then take a torx screwdriver and remove 2 mounting screws. Unplug the wires going into the motor and replace the motor with the new one. But you need to replace the grommet the motor shaft slides up into or it will still leak.