Models > TDB652RBR0

TDB652RBR0 Tappan Dishwasher

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for TDB652RBR0

Viewing 7 of 7

Manuals & Guides for TDB652RBR0

Click to download
Keep searches simple, eg. "belt" or "pump".
Sold individually. Grey in color.
In Stock
This heating element mounting nut is used in dishwashers and is used to hold the nut to prevent leaking. If your nut is damaged or you notice leaking from the dishwasher, then replacing this nut will ...
In Stock
This is a single rack roller kit for your dishwasher. This kit comes with one axel/clip, and one wheel/roller. The kit is used for the lower dishrack, and allows your rack to move freely. You will nee...
In Stock
This is sold individually. Please order quantity required.
In Stock
This one piece dishwasher door gasket provides a water tight seal to keep water from leaking out of your dishwasher.
No Longer Available
NOTE: Sold individually. This door spring is four and a half inches long. It is used for some dishwashers. These springs tend to wear out at the same rate, so you should replace both of your dishwashe...
In Stock
Sold individually.
In Stock
$28.61
This is a basket for your dishwasher. It sits in the lower dishrack and holds small utensils during a washing cycle. This basket has six smaller sections where you can separate your cutlery into speci...
In Stock
Use for the upper rack rollers on the upper rack of your dishwasher.
In Stock
Sold Individually. Order quantity required.
In Stock
Sold individually.
In Stock
Sold individually.
In Stock

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for TDB652RBR0

Viewing 4 of 4
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Not cleaning dishes properly
Fixed by these parts
Fixing Fixing
How to fix it
Door latch failure
Fixed by these parts
Fixing
How to fix it
Not draining
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Dennis from Tryon, NC
Parts Used:
154106202
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench (Adjustable)
Water leaking under the dishwasher
I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwa sher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.
77 of 84 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Darren from Biddeford, ME
Parts Used:
5300809611
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Dishwasher leaked
First I noticed that the old gasket had disintergrated along the bottom. Next I removed the the gasket being careful to observe how it was installed. There are these notched areas of the gasket that belong in the lower corners. I think the notches are designed to help hold the gasket in place and make the gasket bend around the corner. The gasket made closing the door very hard at first but after one wash cycle the fit became much more comfortable. The heat probably made the gasket more pliable. Problem solved.
40 of 45 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Randy from Orlando, FL
Parts Used:
5300809703, 5300809611
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Bad door gasket-leaking, broken door spring
My door spring had broken and I was going to leave it until the door gasket failed and started leaking. After removing the parts, I got on-line and order what I needed. I found everything easier than I thought. I got the parts a few days later and put the gasket in first. Looking at it, you'll find theres slotted ribs at both ends. Those areas go in the bottom corners because of the "S" curve. Simply push in and voila, you're done. At first the door will be firm to shut, but gets better- NO LEAKS! As far as the door spring...you don't have to remove the whole dishwasher. Simply unscrew the bottom plate under the door and reach in, rehook. Piece of cake. This site is wonderful. All the parts and easy to use.
18 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!