Models
>
DW80R7060US
DW80R7060US ((AA-00)) Samsung Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for DW80R7060US
Viewing 8 of 8Keep searches simple, eg. "belt" or "pump".
In Stock
In Stock
$158.37
The tub gasket creates a watertight seal between the dishwasher tub and door.
In Stock
In Stock
In Stock
The drain hose carries drain water from the dishwasher to the drain.
In Stock
$210.42
The drain pump removes the water from the dishwasher tub during the drain phase of the dishwashing cycle. 120V/230
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
TOMMY
January 13, 2024
how do I test the main control board for power?
For model number DW80R7060US
Hello Tommy, thank you for getting in touch. In order to test the main control board for power. Start by placing one of the probes of the meter onto the live pin of the plug. Place the other probe of the meter and place it onto the brown pin on the control panel. The multimeter should read only 1 or 2 ohms or fewer. This will indicate that the power is getting from the plug to the control board but not any further and the dishwasher is dead because the control board is faulty. If, when you do this, you are not getting a reading on the meter, try moving the probe on the board around all the different wires until you do get a reading. When you do get a reading, it will more than likely show the same reading, meaning that the power is getting to the control board but the control board is faulty. If moving the probe around still does not produce any readings, this would indicate there is a fault between the plug and the control board and that is most likely to be in the wiring. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Common Problems and Symptoms for DW80R7060US
Viewing 1 of 1Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from kennewick, WA
- Parts Used:
- DD97-00403E
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
I replaced the pump assembly with a new drain hose
This is not a repair for the faint of heart. You will have to pretty much disassemble the entire dishwasher to replace the main pump assembly. And it’s not cheap, between the pump assembly and the hose...it was over $300...
This dishwasher is Junk...been through 2 motherboards, plastic internal spray arms...and finally a pump a ... Read more ssembly...if you own one and the pump begins to leak....shorts the pump motor out....if it gets this far...but a new dishwasher.
As far as partselect...they are 1st rate.
This dishwasher is Junk...been through 2 motherboards, plastic internal spray arms...and finally a pump a ... Read more ssembly...if you own one and the pump begins to leak....shorts the pump motor out....if it gets this far...but a new dishwasher.
As far as partselect...they are 1st rate.
Read less
Was this instruction helpful to you?
Thank you for voting!