D1471DBK (ABDESEU) LG Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gregory L from INDEPENDENCE, OH
- Parts Used:
- 4970ED4004G
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken door spring allows the door to overextend to the floor if not propped.
Simple, removed screws securing machine in the cabinet, then pull the unit out of the cabinet space about 10 inches. Springs are accessible within this extension. You need strong hands to extend the springs and attach them. Once attached, push machine back in place and re-install the anchor screws. In my situation, only one spring was broken, so the attached side revealed the correct slot to place the hook on the top position, the bottom position has a plastic lead for the spring, and that lead is attached to a rope to the door hinge. Note: Replace BOTH springs, even if only one is broken.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from CHARLOTTE, MI
- Parts Used:
- 3751DD1001J, AHB32983761
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The racks were rusted
We replaced the rusty with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Katy, TX
- Parts Used:
- 3920DD3005H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dishwasher leaking; got AE error almost every other wash
The inside gasket deteriorates over time - However replacement is easy. the main thing you have to remember is after you remove the old gasket, install the new one starting at the middle top of the tub and work your way down both sides. Also, don't push the gasket all the way in...only enough to hold in place. When you close the door the gasket will form a better seal around the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from PLEASANT HILL, CA
- Parts Used:
- ABT72909202
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Leak coming from pump/motor assembly
Ordered complete M030 Casing Assembly (RepairClinic Item # 4116143) after cleaning and testing rubber seal and pump assembly. Worked for two washes, then leak came back. To replace complete assembly, remove dishwasher from under sink, tip on back, disconnect all electrical and connectors to Case Assembly. Next, remove heater assemble (single nut) - this requires upward pulling to release the rubber washer and unit. Once removed unscrew the case assembly (four screws). That's it. Reverse the order to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lenny from KIRTLAND, OH
- Parts Used:
- 4581DD3003C
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Second roller in on the left side was missing don't ask my how, pulling the bottom rack out the rack would dip down i had to lift it up to pull it the rest of the way out.
Ordered the roller from Parts Select, slid the roller over the little spindle sticking out of the bottom rack and snapped it in place. Job done in less than one minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from BOYNTON BEACH, FL
- Parts Used:
- 4581DD3003C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Two Rollers missing on lower tray.
Snapped the rollers on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from SEATTLE, WA
- Parts Used:
- 4027ED3002J
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The door would not stay latched closed (due to moving the dishwasher)
Unscrew all screws on the inside of the dishwasher door. Carefully separate the front panel from the inside panel. Lift out the latch assembly, remove connectors from both sides using needle nose pliers. Reconnect to new assembly and situate back into place. Close front and inside panel, replace all screws, making sure the short and long screws go back to where they came from. Quick easy project to eliminate 2 trips from a repairman, 1 for the diagnosis and 1 to do the work!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from PRATTVILLE, AL
- Parts Used:
- 5001DD4001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Not mounted in place properly
Had to call have an installer attach a metal strip across granite counter top and they did not have the top mount brackets so I had to order them and finish the install. The dishwasher was installed on the side mounts and they missed the cabinets
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from GAYLORD, MI
- Parts Used:
- AHB32983761
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rusty rack and broken wheel
Took out old rack. Put in new rack. Done.
No other assembly required.
No other assembly required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from ITASCA, IL
- Parts Used:
- 4581DD3003C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Roller Assembly was broken
Took off the broken one and snap on the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from LOMPOC, CA
- Parts Used:
- 3920DD3005H
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
There was a leak in the bottom left corner.
I am 77 years old and got it all on but the corners did not want to go in so I had to call my grandson and he got them in. It still leaked on the bottom left side. It is getting old (11 yrs) so I decided to get a new one. It is actually pretty simple to install, but it does take a little strength.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Penelope from LAKEVIEW, MI
- Parts Used:
- 4581DD3003C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Wrong part
The parts are wrong and am trying to return them. There was no return information included with delivery. Calling the Customer Service number for assistance did not work.
I would just like to return these rollers and would like a return address.
Thank you!
Penelope
I would just like to return these rollers and would like a return address.
Thank you!
Penelope
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BIRMINGHAM, AL
- Parts Used:
- AHB33839405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
old rack's coating had split and began to rust
Took a picture of original rack to make sure the new rack placed correctly. Old rack came out without need for tools and the new rack went in with ease after making sure it was facing in the right direction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from WAUWATOSA, WI
- Parts Used:
- 4581DD3003C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Two installed roller wheels came off and broke.
I ordered four wheels to replace the two that were broken and to have two as spares. The wheels are to be snapped onto the bottom of the lower basket. The new wheels broke upon being installed. My extra wheels came in handy. I put them in very hot water for a few minutes to soften the plastic. I put a little Vaseline on the post they were to be attached to. The wheels then slid on and snapped correctly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from RUTHERFORD, NJ
- Parts Used:
- 4027ED3002J
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door latch
Followed the video provided by your company, done like 1,2,3
Was this instruction helpful to you?
Thank you for voting!