D1471DB1 (ABDEEUS) LG Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gregory L from INDEPENDENCE, OH
- Parts Used:
- 4970ED4004G
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken door spring allows the door to overextend to the floor if not propped.
Simple, removed screws securing machine in the cabinet, then pull the unit out of the cabinet space about 10 inches. Springs are accessible within this extension. You need strong hands to extend the springs and attach them. Once attached, push machine back in place and re-install the anchor screws. In my situation, only one spring was broken, so the attached side revealed the correct slot to place the hook on the top position, the bottom position has a plastic lead for the spring, and that lead is attached to a rope to the door hinge. Note: Replace BOTH springs, even if only one is broken.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from CHARLOTTE, MI
- Parts Used:
- 3751DD1001J, AHB32983761
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The racks were rusted
We replaced the rusty with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Katy, TX
- Parts Used:
- 3920DD3005H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dishwasher leaking; got AE error almost every other wash
The inside gasket deteriorates over time - However replacement is easy. the main thing you have to remember is after you remove the old gasket, install the new one starting at the middle top of the tub and work your way down both sides. Also, don't push the gasket all the way in...only enough to hold in place. When you close the door the gasket will form a better seal around the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from PLEASANT HILL, CA
- Parts Used:
- ABT72909202
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Leak coming from pump/motor assembly
Ordered complete M030 Casing Assembly (RepairClinic Item # 4116143) after cleaning and testing rubber seal and pump assembly. Worked for two washes, then leak came back. To replace complete assembly, remove dishwasher from under sink, tip on back, disconnect all electrical and connectors to Case Assembly. Next, remove heater assemble (single nut) - this requires upward pulling to release the rubber washer and unit. Once removed unscrew the case assembly (four screws). That's it. Reverse the order to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg S from BELLE ISLE, FL
- Parts Used:
- 4970ED4004G, 4933DD3001B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door was very heavy due to spring problem
Turn off the power at breaker box. Disconnect the power at dishwasher since I needed to pull the unit all the way out of the cabinet to get to screws on the back side for this model. Find and remove the screws to the cover. Remove cover. In my case, the rope on the connector assembly had snapped. I replaced spring and connector identically to functioning side. Did need a pair of pliers to provide enough tension on spring to install. Reconnected cover and power and moved back into the cabinet. Easy repair and my wife wondered why I hadn't done it sooner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lenny from KIRTLAND, OH
- Parts Used:
- 4581DD3003C
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Second roller in on the left side was missing don't ask my how, pulling the bottom rack out the rack would dip down i had to lift it up to pull it the rest of the way out.
Ordered the roller from Parts Select, slid the roller over the little spindle sticking out of the bottom rack and snapped it in place. Job done in less than one minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Palm coast, FL
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door spring connector
Pull the dishwasher out from underneath the countertop took 2 minutes unscrewed the panel on the side one minute put the connector on one minute screwed the panel back on 1 minute put the dishwasher back underneath the counter two minutes very easy job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from BOYNTON BEACH, FL
- Parts Used:
- 4581DD3003C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Two Rollers missing on lower tray.
Snapped the rollers on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from SEATTLE, WA
- Parts Used:
- 4027ED3002J
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The door would not stay latched closed (due to moving the dishwasher)
Unscrew all screws on the inside of the dishwasher door. Carefully separate the front panel from the inside panel. Lift out the latch assembly, remove connectors from both sides using needle nose pliers. Reconnect to new assembly and situate back into place. Close front and inside panel, replace all screws, making sure the short and long screws go back to where they came from. Quick easy project to eliminate 2 trips from a repairman, 1 for the diagnosis and 1 to do the work!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from PRATTVILLE, AL
- Parts Used:
- 5001DD4001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Not mounted in place properly
Had to call have an installer attach a metal strip across granite counter top and they did not have the top mount brackets so I had to order them and finish the install. The dishwasher was installed on the side mounts and they missed the cabinets
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from San Marcos, CA
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Our dishwasher door would drop open and land on our feet.
My husband was able to slide the dishwasher out, and quickly replace the old connector assembly for the new ones. The old connector assembly had broken at the “rope”. Now the door opens slowly and is as good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from GAYLORD, MI
- Parts Used:
- AHB32983761
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rusty rack and broken wheel
Took out old rack. Put in new rack. Done.
No other assembly required.
No other assembly required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from IRWIN, PA
- Parts Used:
- 4970ED4004G, 4933DD3001B
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Supply line leaked afterwards. Had to replace it. Installers(Home Depot) had it rigged and now it is loose. Going to have to rig it somehow.
Loosened 3 screws and unhooked supply line and electric box and pulled it out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from ELLIJAY, GA
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door would fall to floor
Very easy just took out two screws that held the dishwasher to counter top.Then pulled dishwasher out just far enough that both door cables are exposed.The hardest part for me was getting the spring stretched enough to clip on.This was a easy installation for most people.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from LOMPOC, CA
- Parts Used:
- 3920DD3005H
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
There was a leak in the bottom left corner.
I am 77 years old and got it all on but the corners did not want to go in so I had to call my grandson and he got them in. It still leaked on the bottom left side. It is getting old (11 yrs) so I decided to get a new one. It is actually pretty simple to install, but it does take a little strength.
Was this instruction helpful to you?
Thank you for voting!