KDFE104KWH1 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Judith from Essex, MA
- Parts Used:
- WP8269145
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lost dishwasher brackets
I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from BIRMINGHAM, MI
- Parts Used:
- W11434044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Inlet valve leaking at water connection
The valve has a plastic fitting to attach the the water line with a hose fitting. Was not carful enough with the original and damaged it attaching the water line. Ordered a replacement fitting. While it is possible to replace the water inlet valve without pulling the dishwasher out from the cabinet found it was easier to get at with the machine out. The video does and good job of showing the removal and replacing the valve. Easy job, don't be like me and be careful attaching the water line.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from MADISON, MS
- Parts Used:
- W11412291
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
I was getting the F9 E1 error code intermittently then consistently.
Checked drain hose and it was clear without kinks. I shut of the electrical breaker. Verified no power to washer. Removed the lower trim panel. Lowered the adjustable feet to allow me to slide my unit out. Disconnected drain hose from unit. Pulled unit from cabinet. My drain pump is located on the right bottom side when facing the door of the unit. I did not need to lay the unit on its side and have enough power cable to not have to disconnect it while still pulling the unit all the way out of the cabinet. The pump is easily accessed from the right side hidden behind insulation. Disconnected power wire from pump. Pressed down locking latch and turned pump counter clockwise removed then replaced in opposite order. I have run 3 load’s before posting this and as of now my dishwasher is functioning perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Whit from Pleasanton, CA
- Parts Used:
- W11412291
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Replace dishwasher drain pump
Relatively simple. Unhook electrical, water supply, and hose from drain air gap. Unscrew two screws that hold in the dishwasher and pull it out slowly making sure you do not damage the insulation.
Have a couple of towels nearby because when you tip the dishwasher on it's side some water will spill out.
Locate the old drain pump, disconnect it. Then pull the lever on the side of the pump and twist it off. Check to see if there are any materials that may be blocking the pump. Also good time to clean out the drain line.
Insert the new pump and put everything back in reverse order.
Make sure the dishwasher is level horizontally and vertically.
Have a couple of towels nearby because when you tip the dishwasher on it's side some water will spill out.
Locate the old drain pump, disconnect it. Then pull the lever on the side of the pump and twist it off. Check to see if there are any materials that may be blocking the pump. Also good time to clean out the drain line.
Insert the new pump and put everything back in reverse order.
Make sure the dishwasher is level horizontally and vertically.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tamera from McKinney, TX
- Parts Used:
- W11778050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Bottom dishrack had several exposed rusted prongs
I searched for another dishrack that was compatible with our unit. After measuring and searching online I found Partselect website and placed the order. It was a very easy process. I bought the rack without wheels and just removed the ones from our current bottom rack and put them on the new rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from N KINGSTOWN, RI
- Parts Used:
- W11434044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Hose threads stripped
I found it best to lay the dishwasher on it's side, this makes it easier to attach a 90 degree hose fitting without cross threading the plastic fitting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from HIGGINSVILLE, MO
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Mounting bracket
Removed old part and replaced with new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from ROLLA, MO
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
installer from lowes di not do it right, forgot to put scew in, instead he used shims, as usuall no more installs from Lowes
followed directions, a kid could have done it,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerould from East Wenatchee, WA
- Parts Used:
- W11412291
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwasher would not completely drain e1 f9 error
Pulled the dishwasher out from under counter - removing 2 screws accessible on sides of dishwasher - these screws hold dishwasher under counter. Drain pump accessible right side bottom. Disconnect wiring clip - grab pump turn counter clockwise 1/4 turn and pull out of housing. Then reverse this process for installation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Sterling Heights, MI
- Parts Used:
- W11551775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Warranty Service lost the two screws that held the cover below the door in place
It’s great when you have parts that fit and a schematic to go by. I got both from this site. There are three parts that these screws hold in place. Use the schematic to see which way each part is facing. Line all the parts up and then look through the covers. You’ll see pre drilled holes on either side of the cover. Line the screws up to the pre drilled holes. Put the first screw in half way then insert the second screw all the way. Come back to the first screw and tighten it all the way. Two screws, two minutes and I was done. Real easy repair, just awkward as you are on your belly on the floor. I used a drill with a socket that fit the screw head.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Carol Stream, IL
- Parts Used:
- WPW10348409
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screws on the door of the dishwasher were very loose.
Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antony from Lakewood Ranch, FL
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Dishwasher was not firmly connected to the counter
Very simple repair when you're supplied with the proper parts. Their delivery time is exceptional !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Maple Valley, WA
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Under Counter Anti-Tip Brackets Broke
I put this unit in about 3 years ago and the brackets broke at the crease and the dishwasher fell forward. Found the right bracket and when it arrived looked a match. Checked link to video showing how to properly install the brackets. The original manufacturer never stated that the tab that goes through the frame is supposed to be bent 90 degrees to prevent the bracket from coming out. Thank you PartSelect for that video because I would probably end up ordering brackets again in a few years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Montrose, CO
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
I had not needed to install the mounting brackets that came with the dishwasher because the old counter top was 1 inch lower than standard and I was able to just wedge the dishwasher into the space and it would not tip.
I simply disconnected the power line to the dishwasher and pulled it out enough to install the mounting brackets. The installation manual that came with the dishwasher described how to install the brackets and I simply followed directions.
Was this instruction helpful to you?
Thank you for voting!