Models
>
KUDP01DLBL7
KUDP01DLBL7 KitchenAid Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for KUDP01DLBL7
Viewing 11 of 11
Manuals & Guides for KUDP01DLBL7
Click to downloadKeep searches simple, eg. "belt" or "pump".
$33.12
If your dishwasher door is not opening or closing properly, it may be time to install a new balance kit. This part helps to support the weight of the door as it opens and closes. You should also check...
In Stock
Order within the next 57 mins and your part ships today!
$10.04
The mounting bracket is used to secure the top part of your dishwasher to the underside of your counter or cabinet. If you have solid surface counters (granite, quartz, etc.) you will likely need to s...
In Stock
Order within the next 57 mins and your part ships today!
$53.49
If the silverware basket in your dishwasher has become damaged, this is a certified OEM replacement. Continuing to use a damaged silverware basket can result in your cutlery not being cleaned properly...
In Stock
Order within the next 57 mins and your part ships today!
$34.77
If your dishwasher is not cleaning your dishes properly, is not draining, or is noisy while operating, there may be an issue with your chopper assembly. The chopper is used to mince up food particles ...
In Stock
Order within the next 57 mins and your part ships today!
$44.70
This part contains the mounting clips and helps distribute water from the top of the dishwasher tub.
In Stock
Order within the next 57 mins and your part ships today!
In Stock
Order within the next 57 mins and your part ships today!
$35.44
When replacing these fuses the wire harness must be replaced as well. It is located in the control panel. The harness is included with this part now.
In Stock
Order within the next 57 mins and your part ships today!
$94.70
The door gasket provides a water tight seal, between the tub and the door, to keep water from leaking out of your dishwasher. If the dishwasher is leaking you may need to replace the door gasket. Thi...
In Stock
Order within the next 57 mins and your part ships today!
In Stock
Order within the next 57 mins and your part ships today!
$68.21
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve will open and close according to the desired amount of water needed.
In Stock
Order within the next 57 mins and your part ships today!
In Stock
Order within the next 57 mins and your part ships today!
In Stock
Order within the next 57 mins and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for KUDP01DLBL7
Viewing 10 of 10Not cleaning dishes properly
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Not draining
Fixed by these parts
How to fix it
Not drying dishes properly
Fixed by these parts
How to fix it
Will not dispense detergent
Fixed by these parts
How to fix it
Will not fill with water
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from Fort Lauderdale, FL
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced Hinge Link
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from North Richland Hills, TX
- Parts Used:
- W10083957V
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Dishes on top rack of dishwasher were not being cleaned.
1) Remove top and bottom dish baskets from the dishwasher, this will give you room to work. To remove top basket there are clips at the end of the slide rails.
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube th ... Read more at takes water to the middle and top spray arms. Unclip this tube from the top and middle clips and then work it out of the strainer assembly tube. Now you should be able to remove the tube at the bottom of the dishwasher by unscrewing it 1/4 turn.
4) Remove the strainer cover by unscrewing the 4 Torqs screws.
5) You will now see two smaller torqs screws that hold the hold the Chopper Assembly cover down. Take these two screws out and remove the two piece cover.
6) Pull out the broken Chopper Assembly, make sure you get all the pieces!
7) Install the new Chopper Assembly. Make sure that you install the Assembly with the small part of the screen towards the bottom of the housing. Also make sure you compress the spring as you install the part. I used a small pair of neddle nose pliers to compress the spring behind the screen in order to install the chopper assembly.
8) Put everything back together and make sure it works!
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube th ... Read more at takes water to the middle and top spray arms. Unclip this tube from the top and middle clips and then work it out of the strainer assembly tube. Now you should be able to remove the tube at the bottom of the dishwasher by unscrewing it 1/4 turn.
4) Remove the strainer cover by unscrewing the 4 Torqs screws.
5) You will now see two smaller torqs screws that hold the hold the Chopper Assembly cover down. Take these two screws out and remove the two piece cover.
6) Pull out the broken Chopper Assembly, make sure you get all the pieces!
7) Install the new Chopper Assembly. Make sure that you install the Assembly with the small part of the screen towards the bottom of the housing. Also make sure you compress the spring as you install the part. I used a small pair of neddle nose pliers to compress the spring behind the screen in order to install the chopper assembly.
8) Put everything back together and make sure it works!
Read less
Was this instruction helpful to you?
Thank you for voting!
Controller board replacement
Simple task - remove the front door cover to expose the cover for the control panel which is then also removed. Be sure electricity is disconnected from the appliance, then simply remove the old control board (remove the quick-connect wire harness) and slide the replacement board back in. Reconnect wiring harness, replace cover and door p
... Read more
anel, then turn-on electricy. NOTE - I suggest you shut off power at the breaker panel vs. disconnected the direct wiring at the appliance. The reason for this is because the new controller board could be damaged in the process of connecting the wires and any sparking that would take place when working with hot wiring.
Read less
Was this instruction helpful to you?
Thank you for voting!