Models
>
58714659200A
58714659200A Kenmore Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 58714659200A
Viewing 4 of 4
Manuals & Guides for 58714659200A
Click to downloadKeep searches simple, eg. "belt" or "pump".
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
In Stock
Order within the next 11 hrs and your part ships today!
Special Order
This part carries the drain water from the appliance to the drain. It is white in color.
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 58714659200A
Viewing 6 of 6Leaking
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Not cleaning dishes properly
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Will not fill with water
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from Cutchogue, NY
- Parts Used:
- 5304535183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken latch
removed front face of dishwasher removed 2 screws holding latch and removed 2 push in plugs reinstalled the same.
job completed in less than 15 min.
job completed in less than 15 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Belmont, CA
- Parts Used:
- 5304482406
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Water leaking out onto floor when not in use!
Remove front Fascia on floor, use AC sniffer find hot wires into unit. Flip circuit breaker at panel. Verify no AC, shut water valve off on Dishwasher supply. Disconnect two valve wires to solenoid. Use wrench set to find proper size and use to remove supply line. Unscrew two Phillips sheet metal screws that hold valve support bracket and
... Read more
remove bracket with it now being held in by water inlet valve hose to interior wall of Dishwasher. Use Tin Snips to cut off metal band securing hose to old water inlet valve. Place new valve onto inlet hose, secure with new hose clamp (you must supply) tighten hex nut on clamp till water tight. Fasten wires onto the solenoid and mount assembly support bracket to dishwasher. Now connect water supply line after wrapping threads with pipe dope tape fasten and secure nut with adjustable wrench till water tight open supply valve and look for leaks with a flash light. If no leaks, reset breaker and test run and drain. No leaks replace fascia and have a Beer great Job saved $850 min. on a new dishwasher!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from West Farmington, ME
- Parts Used:
- 5304483509
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
A very tiny plastic washer in the assembly was bad. It kept coming out. I put it back several times and then ordered a whole new assembly.
I unscrewed the old one and screwed in the new one. 2 hose fittings. Had anyone made real parts, I could have replaced the washer.
Was this instruction helpful to you?
Thank you for voting!