Models
>
66513283K114
66513283K114 Kenmore Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 66513283K114
Viewing 12 of 12
Keep searches simple, eg. "belt" or "pump".
This rack adjuster kit is connected to the dishrack and allows you to adjust the height of the upper rack of your dishwasher up and down to give more space. The kit is constructed of gray plastic and ...
In Stock
Order within the next 8 hrs and your part ships today!
$8.10
The genuine OEM replacement rack stop clip is for dishwashers. It measures just over an inch and is made of gray plastic. The purpose of this part is to prevent your dishwasher rack from pulling out t...
In Stock
Order within the next 8 hrs and your part ships today!
$10.04
The mounting bracket is used to secure the top part of your dishwasher to the underside of your counter or cabinet. If you have solid surface counters (granite, quartz, etc.) you will likely need to s...
In Stock
Order within the next 8 hrs and your part ships today!
$66.15
This is a manufacturer-approved heating element and 2 washers. If the dishes in your dishwasher are not drying or the water in the dishwasher is not getting hot, it may be due to a failed heating elem...
In Stock
Order within the next 8 hrs and your part ships today!
This black rubber gasket is a genuine OEM replacement part for your dishwasher door. The gasket helps to provide a tight seal between the door and the tub, preventing water from leaking while the appl...
In Stock
Order within the next 8 hrs and your part ships today!
$38.25
The dishwasher positioner clip is also known as a rack adjuster and is used to hold the top rack in your dishwasher in the desired position. If the rack is not staying in place, the clip may have beco...
In Stock
Order within the next 8 hrs and your part ships today!
$91.96
If there is still water left in your dishwasher after it has finished running, there may be an issue with your drain pump. The pump is designed to remove water from the tub, and if that is not happeni...
In Stock
Order within the next 8 hrs and your part ships today!
$7.50
The friction sleeve, sometimes called a friction pad, is made of a flexible black plastic and measures a bit over one inch in length. It is designed to reduce the friction between the hinge and the do...
In Stock
Order within the next 8 hrs and your part ships today!
$49.58
This is an authentic OEM replacement drawer track for the upper rack of your dishwasher. Also known as a rack slider bar, it helps to support the top rack and allows it to glide in and out of your dis...
In Stock
Order within the next 8 hrs and your part ships today!
$46.08
The dishrack adjuster, also known as an adjuster clip, is used to change the height of the top rack in your dishwasher. If the clip has become damaged, it may not function properly, which would result...
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!
In Stock
Order within the next 8 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 66513283K114
Viewing 10 of 10Leaking
Fixed by these parts
How to fix it
Not drying dishes properly
Fixed by these parts
How to fix it
Not cleaning dishes properly
Fixed by these parts
How to fix it
Not draining
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Will not fill with water
Fixed by these parts
How to fix it
Will not dispense detergent
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from Encinitas, CA
- Parts Used:
- W10712394
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace rack adjusters - wheel were broken
Replacement was pretty easy after figuring out how to unsnap/unlock the old pieces. Tools only used to do a little prying and poking, but really aren't needed. Everything either snaps or slides together. Piece of cake
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walton from Chittenango, NY
- Parts Used:
- W10712394
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
broken rollers on upper basket
I took the broken basket adjuster off and then attached the new one. It wasn't too difficult, however some removal instructions and re-install instructions( or just a picture supplied) would have been helpful. This isn't an issue for a mechanically inclined person, but would be a challenge for someone that isn't. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Alexandria, VA
- Parts Used:
- WPW10348269
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release
... Read more
the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
Read less
Was this instruction helpful to you?
Thank you for voting!