58717242100 Kenmore Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sandra from Mount Vernon, WA
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower Rack Roller Missing
Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Milton, FL
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dishwasher was leaking water
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Princeton, NC
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
plastic handle broke
First I removed and replaced the gasket around the tub. It didn't require any tools and took about 2 minutes to complete. I didn't really need to replace the gasket but it came with the latch kit so I went ahead and replaced it anyway. Than I removed only the top door panel (6 screws) and supported it while I removed the broken latch (2 Torx screws). I had to use a pair of needle nose pliers to pull the wires off the old latch (keeping track of where each wire came from) then plugged the wires onto the new latch and screwed it back to the door. Put the door panel back in place with the 6 screws I had removed earlier and I was done. it all took about 15 minutes and the wife is so glade she is not doing dishes by hand anymore that she left me alone for the rest of the night.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Phoenix, AZ
- Parts Used:
- 154574401
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch on detergent dispenser was broken
Reading the instructions posted, I realized that I only needed to remove the two lower screws on the inside of the dishwasher door. The lower front panel then came off easily. I unplugged the power to the dishwasher. I then removed the six screws holding the dispenser in place, and when loose I unplugged the two wires (I used a flat blade screwdrive to pry them a bit then they slid off -- note the red one was inside, lighter one outside). I put the new part in, put in all but the left screw with the hook. I then plugged the wires in, and fastened the left screw with the hook positioned around the wires. I put the panel back on, fastenet the two screws that hold it in, and plugged the dishwasher back in. It's working beautifully. All in all it was about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Pleasant View, UT
- Parts Used:
- 154827601, 154597801, 5304507405, 5303943103, 5304535381
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Top rack was dropping out of rollers/Slides
This was the second part of repair. Left side was constantly falling out of the slide. I replaced the same items as above minus the gasket and screw kit. Once done, the right side was sloppy so I orders part for that side plus gasket which slid right in.
1. Removed stops on front end of Upper Dishrack Slide on both sides.
2. Removed Upper Dishrack
3. Remove Roller and Axle/clip (4 each)
4. Push Roller onto Axle on all 4 kits
5. Install all 4 roller kits on Upper Dishrack
6. Remove stops from back end of Upper Dishrack Slides.
7. Remove both Slides
8. Remove 8 each Tub Wheels.
9. Using old or new Screws and Washers, install new Tub Wheels.
10. Install both Upper Dishrack Slides ensuring that small holes are toward the back.
11. Install stops on the back end of Slides.
12 Install Upper Dishrackinto slides
13. Install front stops on slide
14. Pulled out Gasket
15. Install replaced Gasket
1. Removed stops on front end of Upper Dishrack Slide on both sides.
2. Removed Upper Dishrack
3. Remove Roller and Axle/clip (4 each)
4. Push Roller onto Axle on all 4 kits
5. Install all 4 roller kits on Upper Dishrack
6. Remove stops from back end of Upper Dishrack Slides.
7. Remove both Slides
8. Remove 8 each Tub Wheels.
9. Using old or new Screws and Washers, install new Tub Wheels.
10. Install both Upper Dishrack Slides ensuring that small holes are toward the back.
11. Install stops on the back end of Slides.
12 Install Upper Dishrackinto slides
13. Install front stops on slide
14. Pulled out Gasket
15. Install replaced Gasket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Souderton, PA
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door latch was broken
It was easy to replace the latch. 4 screws to take the cover off... two star screws for the latch assy. and 4 wires. NOTE: be sure to kill the power to the washer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marla from Columbia, TN
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic attachment for wheel to rack had dried and broken
removed the remnants of the old wheels and popped the new ones on....simple
Got to say, I was pretty amazed that I received my order the following day! You guys are wonderful!
Got to say, I was pretty amazed that I received my order the following day! You guys are wonderful!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Landis, NC
- Parts Used:
- 5304532229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing 2 rollers in lower basket
Alighned the bracket and pushed in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Virginia Beach, VA
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher won't start
Be aware that there is a Child Lock Control on this dishwasher. To unlock the controls, press the POWER DRY OFF/NO HEAT DRY pad for 5 seconds until the CONTROLS light goes out.
If that doesn't work then read on.
I noticed the plastic handle was very loose in its opening. So I removed the screws along the interior edge of the door to expose the Door Latch Assembly. (Be careful. The two lowest screws- closest to the hinges- hold the metal door trim panel in place after sliding the panel over two clips near the screws. If you don't hold the door panel it may fall and get scratched. Put a bath towel or rug on the floor to avoid scratching it.)
After removing the phillips head screws, (and keeping track of the different size lengths in each position) I found the plastic handle broken at its fulcrum with the loose parts rattling around the inside of the door. The microswitches that tell the control panel the door is closed were not being pressed when the door closed because the broken handle was loose. I orderd the part I needed, got it in 5 days and reopened the door. The Door Latch Assembly is held in place with two medium size TORX head screws. Just remove each of the 4 electrical connectors one at a time from the old door latch assembly (that includes a new plastic handle) and attach to the new switch in the same order you remove them. After reassembling, I had the machine running in just a few minutes.
If that doesn't work then read on.
I noticed the plastic handle was very loose in its opening. So I removed the screws along the interior edge of the door to expose the Door Latch Assembly. (Be careful. The two lowest screws- closest to the hinges- hold the metal door trim panel in place after sliding the panel over two clips near the screws. If you don't hold the door panel it may fall and get scratched. Put a bath towel or rug on the floor to avoid scratching it.)
After removing the phillips head screws, (and keeping track of the different size lengths in each position) I found the plastic handle broken at its fulcrum with the loose parts rattling around the inside of the door. The microswitches that tell the control panel the door is closed were not being pressed when the door closed because the broken handle was loose. I orderd the part I needed, got it in 5 days and reopened the door. The Door Latch Assembly is held in place with two medium size TORX head screws. Just remove each of the 4 electrical connectors one at a time from the old door latch assembly (that includes a new plastic handle) and attach to the new switch in the same order you remove them. After reassembling, I had the machine running in just a few minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Fond Du Lac, WI
- Parts Used:
- 154574401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dishasher Soap/Rinse Dispenser
The latch on the soap dispenser got worn out over the past few years on the dishwasher. I tried just puting the detergent into it and running it as usual. The detergent was added Immediatley.. missing the proper timing that would normally dispense it properly. As a result the dishes were not coming out clean and lacked the shiny clean quality we were accustomed to . I ordered the right part, got it quickly and put it in..and were back to doing dishes and having them come out the right way...spotless and clean like they should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from virginia beach, VA
- Parts Used:
- 154773201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No water to dish washer
After figuring out the problem wasn't the water inlet switch, I replaced the switch assembly for the water level float. Cut off supply water to dishwasher, removed the 2 screws holding switch assembly, and installed new switch. 15 minutes, very easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hummelstown, PA
- Parts Used:
- 154827601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher was leaking at the lower left side of the door.
Probably the easiest repair job that you could encounter. I removed the old gasket from the door frame. Cut the new gasket to length and pushed it into the door frame.
Water leak solved...
Water leak solved...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Columbus, OH
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Door latch broken
Removed eight screws holding front panel to door; placed blanket below it beforehand based on tip read in another person’s post. Removed two screws holding switch in place and then transferred four wire connectors one at a time. Replaced latch assembly with two screws. Replaced front door panel by reinstalling eight previously removed screws then did a load of dishes.
I was impressed with the user friendly format of your web site. I was able to quickly look up the part I needed. It arrived much faster than I expected after my order was placed.
I have already recommended the site to a friend needing parts for a Gibson dishwasher.
I was impressed with the user friendly format of your web site. I was able to quickly look up the part I needed. It arrived much faster than I expected after my order was placed.
I have already recommended the site to a friend needing parts for a Gibson dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Lorena, TX
- Parts Used:
- 5304442175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not start; no control lights illuminated.
Replaced door switch as follows: (1) turned off circuit breaker powering unit; (2)removed six screws holding front control panel cover to chasis and pulled cover out slightly to expose switch; (3) labelled four connectors on wires to switch with marking pen; (4) disconnected the four wires: (5) removed two screws holding switch to chasis; (6)installed new switch with the two screws; (7) reconnected the four wires; (8)replaced cover panel and (9) turned circuit breaker back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra R. from Groveland, FL
- Parts Used:
- 5304523457
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Old hose was split
The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job
Was this instruction helpful to you?
Thank you for voting!