Models
>
66513202N413
66513202N413 Kenmore Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 66513202N413
Viewing 10 of 10
Keep searches simple, eg. "belt" or "pump".
This OEM dishwasher upper rack adjuster kit includes the left and ride side adjusters and all the parts needed to repair the upper rack. These parts have changed from plastic to metal, so even though ...
In Stock
$7.71
This is a single rack track stop clip used to prevent the upper dish rack from sliding all the way out of the dishwasher. It is made of gray plastic and can wear with time. This is an easy repair that...
In Stock
$10.04
The mounting bracket is used to secure the top part of your dishwasher to the underside of your counter or cabinet. If you have solid surface counters (granite, quartz, etc.) you will likely need to s...
In Stock
$66.15
This is a manufacturer-approved heating element and 2 washers. If the dishes in your dishwasher are not drying or the water in the dishwasher is not getting hot, it may be due to a failed heating elem...
In Stock
$38.25
The dishwasher positioner clip is also known as a rack adjuster and is used to hold the top rack in your dishwasher in the desired position. If the rack is not staying in place, the clip may have beco...
In Stock
$7.50
The friction sleeve, sometimes called a friction pad, is made of a flexible black plastic and measures a bit over one inch in length. It is designed to reduce the friction between the hinge and the do...
In Stock
In Stock
$26.74
The retainer clip is used to hold the access panel on your dishwasher in place. It is a genuine OEM part that is black in color and sold individually. The only tool required to complete the repair is ...
In Stock
$64.02
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
In Stock
$58.02
This genuine OEM filter is found under the lower spray arm in the bottom of your dishwasher. It is used to trap debris and prevent it from entering the pump. If your dishes are not properly cleaned or...
In Stock
$254.70
If you need a new lower dishrack for your dishwasher, this is a genuine OEM replacement part. The rack is gray in color and is used to hold your dishes in place while the appliance is operating. Pleas...
In Stock
$20.71
This part acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this part will shut down power to the heating element.
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 66513202N413
Viewing 10 of 10Leaking
Fixed by these parts
How to fix it
Not drying dishes properly
Fixed by these parts
How to fix it
Not cleaning dishes properly
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Will not fill with water
Fixed by these parts
How to fix it
Not draining
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Will not dispense detergent
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dennis from Sedro Woolley, WA
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Heater element broken.
Step 1: Remove the screws in the bottom of the countertop.
Step 2: Remove the screws holding the bottom kickplate.
Step 3: Loosen leveling legs.
Step 4: Pull dishwasher out of hole.
Step 5: Unlplug dishwasher.
Step 6: Disconnect wires from bottom of element in back.
Step 7: ... Read more Remove plastic nuts holding element in place.
Step 8: Remove element.
Step 9: Reverse Steps 1-7.
Step 10: Drink beer.
Step 2: Remove the screws holding the bottom kickplate.
Step 3: Loosen leveling legs.
Step 4: Pull dishwasher out of hole.
Step 5: Unlplug dishwasher.
Step 6: Disconnect wires from bottom of element in back.
Step 7: ... Read more Remove plastic nuts holding element in place.
Step 8: Remove element.
Step 9: Reverse Steps 1-7.
Step 10: Drink beer.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Essex, MA
- Parts Used:
- WP8269145
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lost dishwasher brackets
I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from OAKLAND, CA
- Parts Used:
- W10712395
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Instruction from Whirlpool Not Good (No problem with Part Select)
Trial and error. The instructions from Whirlpool included with the part had minuscule pictures so it was hard to follow. The written instructions were good. But "a picture is worth a thousand words." Eventually it worked. The metal replacement part is much better the the plastic original. Not a good reflection on Whirlpool.
Was this instruction helpful to you?
Thank you for voting!