Models
>
66516032400
66516032400 Kenmore Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Manuals & Guides for 66516032400
Click to downloadKeep searches simple, eg. "belt" or "pump".
$7.71
This is a single rack track stop clip used to prevent the upper dish rack from sliding all the way out of the dishwasher. It is made of gray plastic and can wear with time. This is an easy repair that...
In Stock
$10.04
The mounting bracket is used to secure the top part of your dishwasher to the underside of your counter or cabinet. If you have solid surface counters (granite, quartz, etc.) you will likely need to s...
In Stock
$66.15
This is a manufacturer-approved heating element and 2 washers. If the dishes in your dishwasher are not drying or the water in the dishwasher is not getting hot, it may be due to a failed heating elem...
In Stock
$63.79
This is a genuine OEM replacement silverware basket for your dishwasher. The basket measures approximately 19.5 inches long, 4 inches wide, and 9 inches high. It is made of gray-colored plastic and in...
In Stock
This black rubber gasket is a genuine OEM replacement part for your dishwasher door. The gasket helps to provide a tight seal between the door and the tub, preventing water from leaking while the appl...
In Stock
$34.77
If your dishwasher is not cleaning your dishes properly, is not draining, or is noisy while operating, there may be an issue with your chopper assembly. The chopper is used to mince up food particles ...
In Stock
$27.59
This part includes one OEM rinse aid cap (also known as a dispenser cap), and its purpose is to cover the rinse aid dispenser located on the dishwasher door. Please note that this manufacturer-approve...
In Stock
$7.50
The friction sleeve, sometimes called a friction pad, is made of a flexible black plastic and measures a bit over one inch in length. It is designed to reduce the friction between the hinge and the do...
In Stock
$35.44
When replacing these fuses the wire harness must be replaced as well. It is located in the control panel. The harness is included with this part now.
In Stock
$29.52
This is also called the 3rd-level spinner. This part works like a little spray arm at the top of your dishwasher.
In Stock
$68.21
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve will open and close according to the desired amount of water needed.
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 66516032400
Viewing 10 of 10Not cleaning dishes properly
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Not drying dishes properly
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Not draining
Fixed by these parts
How to fix it
Will not dispense detergent
Fixed by these parts
How to fix it
Will not fill with water
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bill from North Richland Hills, TX
- Parts Used:
- W10083957V
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Dishes on top rack of dishwasher were not being cleaned.
1) Remove top and bottom dish baskets from the dishwasher, this will give you room to work. To remove top basket there are clips at the end of the slide rails.
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube th ... Read more at takes water to the middle and top spray arms. Unclip this tube from the top and middle clips and then work it out of the strainer assembly tube. Now you should be able to remove the tube at the bottom of the dishwasher by unscrewing it 1/4 turn.
4) Remove the strainer cover by unscrewing the 4 Torqs screws.
5) You will now see two smaller torqs screws that hold the hold the Chopper Assembly cover down. Take these two screws out and remove the two piece cover.
6) Pull out the broken Chopper Assembly, make sure you get all the pieces!
7) Install the new Chopper Assembly. Make sure that you install the Assembly with the small part of the screen towards the bottom of the housing. Also make sure you compress the spring as you install the part. I used a small pair of neddle nose pliers to compress the spring behind the screen in order to install the chopper assembly.
8) Put everything back together and make sure it works!
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube th ... Read more at takes water to the middle and top spray arms. Unclip this tube from the top and middle clips and then work it out of the strainer assembly tube. Now you should be able to remove the tube at the bottom of the dishwasher by unscrewing it 1/4 turn.
4) Remove the strainer cover by unscrewing the 4 Torqs screws.
5) You will now see two smaller torqs screws that hold the hold the Chopper Assembly cover down. Take these two screws out and remove the two piece cover.
6) Pull out the broken Chopper Assembly, make sure you get all the pieces!
7) Install the new Chopper Assembly. Make sure that you install the Assembly with the small part of the screen towards the bottom of the housing. Also make sure you compress the spring as you install the part. I used a small pair of neddle nose pliers to compress the spring behind the screen in order to install the chopper assembly.
8) Put everything back together and make sure it works!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Inver Grove Heights, MN
- Parts Used:
- WPW10757217
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Loud grinding noise from water pump
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull
... Read more
it out. Then put the new one in. That was the easy part (about 15 minutes). The entire job took 2-and-a-half hours, most of which was taken in disconnecting, cleaning up and reconnecting the dishwasher. It's much quieter now.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Sedro Woolley, WA
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Heater element broken.
Step 1: Remove the screws in the bottom of the countertop.
Step 2: Remove the screws holding the bottom kickplate.
Step 3: Loosen leveling legs.
Step 4: Pull dishwasher out of hole.
Step 5: Unlplug dishwasher.
Step 6: Disconnect wires from bottom of element in back.
Step 7: ... Read more Remove plastic nuts holding element in place.
Step 8: Remove element.
Step 9: Reverse Steps 1-7.
Step 10: Drink beer.
Step 2: Remove the screws holding the bottom kickplate.
Step 3: Loosen leveling legs.
Step 4: Pull dishwasher out of hole.
Step 5: Unlplug dishwasher.
Step 6: Disconnect wires from bottom of element in back.
Step 7: ... Read more Remove plastic nuts holding element in place.
Step 8: Remove element.
Step 9: Reverse Steps 1-7.
Step 10: Drink beer.
Read less
Was this instruction helpful to you?
Thank you for voting!