Models
>
666515932000
666515932000 Kenmore Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$33.12
If your dishwasher door is not opening or closing properly, it may be time to install a new balance kit. This part helps to support the weight of the door as it opens and closes. You should also check...
In Stock
$7.71
This is a single rack track stop clip used to prevent the upper dish rack from sliding all the way out of the dishwasher. It is made of gray plastic and can wear with time. This is an easy repair that...
In Stock
$10.04
The mounting bracket is used to secure the top part of your dishwasher to the underside of your counter or cabinet. If you have solid surface counters (granite, quartz, etc.) you will likely need to s...
In Stock
$63.79
This is a genuine OEM replacement silverware basket for your dishwasher. The basket measures approximately 19.5 inches long, 4 inches wide, and 9 inches high. It is made of gray-colored plastic and in...
In Stock
This black rubber gasket is a genuine OEM replacement part for your dishwasher door. The gasket helps to provide a tight seal between the door and the tub, preventing water from leaking while the appl...
In Stock
If you are unable to smoothly roll the top dish rack of your dishwasher, you may need to replace some of the wheel assemblies. Over time they can become cracked and damaged, and once this happens, the...
In Stock
$35.44
When replacing these fuses the wire harness must be replaced as well. It is located in the control panel. The harness is included with this part now.
In Stock
$68.21
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve will open and close according to the desired amount of water needed.
In Stock
In Stock
This part releases the detergent and rinse aid into the dishwasher.
In Stock
$13.67
This part is the top spinner located at the very top of the wash tub. Water passes through all the spinners causing it to dispense all around the tub.
In Stock
$222.51
The part functions by spinning the impeller of the circulation pump, which is used to move the water through the spray arms during the wash cycle.
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 666515932000
Viewing 10 of 10Leaking
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Not cleaning dishes properly
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Not draining
Fixed by these parts
How to fix it
Will not dispense detergent
Fixed by these parts
How to fix it
Will not fill with water
Fixed by these parts
How to fix it
Not drying dishes properly
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from Fort Lauderdale, FL
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced Hinge Link
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Inver Grove Heights, MN
- Parts Used:
- WPW10757217
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Loud grinding noise from water pump
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull
... Read more
it out. Then put the new one in. That was the easy part (about 15 minutes). The entire job took 2-and-a-half hours, most of which was taken in disconnecting, cleaning up and reconnecting the dishwasher. It's much quieter now.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Fanwood, NJ
- Parts Used:
- WP8558129
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
dispenser door was not closing
1. Remove torx screws around outer edge of inside of door.
2. Separate outer door panel from inner door panel.
3. Locate dispenser, and remove 6 hex nuts and 2 wires for solenoid.
4. Insert new dispenser and re-insert hex nuts.
5. Reinsert torx screws.
2. Separate outer door panel from inner door panel.
3. Locate dispenser, and remove 6 hex nuts and 2 wires for solenoid.
4. Insert new dispenser and re-insert hex nuts.
5. Reinsert torx screws.
Was this instruction helpful to you?
Thank you for voting!