Models > KABD2405MW1B

KABD2405MW1B Kelvinator Dishwasher

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for KABD2405MW1B

Viewing 7 of 7

Manuals & Guides for KABD2405MW1B

Click to download
Keep searches simple, eg. "belt" or "pump".
This dishwasher door gasket is attached to the bottom of the door, creating a strong seal between the tub and the outer edge of the door. This seal is prone to wear and tear due to its constant exposu...
In Stock
This is a single lower spray arm found in dishwashers to spray water and detergent vigorously over the dishes. This spray arm is made of plastic, so can warp or crack with time. The holes in the spray...
In Stock
The door gasket provides a watertight seal between the tub and the door, to keep water from leaking out of your dishwasher. If your dishwasher is leaking you may need to replace the door gasket. This ...
In Stock
This is a single rack roller kit for your dishwasher. This kit comes with one axel/clip, and one wheel/roller. The kit is used for the lower dishrack, and allows your rack to move freely. You will nee...
In Stock
This is a genuine OEM replacement water inlet valve for your dishwasher. The water inlet valve supplies water to the dishwasher by opening and closing the solenoids attached to the valve, depending on...
In Stock
Sold individually. Grey in color.
In Stock
This heating element mounting nut is used in dishwashers and is used to hold the nut to prevent leaking. If your nut is damaged or you notice leaking from the dishwasher, then replacing this nut will ...
In Stock
The drain hose connects to the pump located below the lower spray arm. It aids in proper dishwasher drainage. Size: 7.5 feet long
In Stock
If your dishwasher is leaking from the corners of the gasket, you may need to replace the splash shields. The splash shields attach to the lower front corners of dishwasher and are used to prevent wat...
In Stock
This genuine OEM part is a lower spray arm support for your dishwasher. It is found in the bottom of the dishwasher and is the piece that the lower spray arm attaches to. If this part has become damag...
In Stock
In Stock
The drain pump ejects the water from the dishwasher.
In Stock

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for KABD2405MW1B

Viewing 10 of 10
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Not cleaning dishes properly
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Not draining
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not fill with water
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door latch failure
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not dispense detergent
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door won’t close
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Not drying dishes properly
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
CHRIS from ROANOKE, VA
Parts Used:
154637401, 5304532229
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Water leaking from Inlet Valve
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it leaked in the first place and messed up my subfloor and laminate flooring.
620 of 635 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sandra from Mount Vernon, WA
Parts Used:
5304532229
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Lower Rack Roller Missing
Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new.
376 of 383 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from Flowood, MS
Parts Used:
809006501
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Bottom Door Seal fell apart and started leaking.
First I opened the door all the way. Second I reached down to the bottom gasket then grabed it on the right end of the seal that is on the right side of the door. Then I pulled the end outward from the bottom of the door toward the heater coil in the bottom of the washer. It came out real easy. You see it just snaps into a little plastic groove under the door. I then cleaned up the area for food and soap particules. I then placed the new gasket in place by lining up the notch toward the right end with the piece of plastic that encloses the right end of the plastic notch on the bottom right end of the door. Then push it in untill it stops going into the notch. It snaps in but does not make a snaping sound. It just won't go in no more.
381 of 429 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!