Models > DP400PWD1

DP400PWD1 Kelvinator Dishwasher

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for DP400PWD1

Viewing 9 of 9
Keep searches simple, eg. "belt" or "pump".
Sold individually. Grey in color.
In Stock
This heating element mounting nut is used in dishwashers and is used to hold the nut to prevent leaking. If your nut is damaged or you notice leaking from the dishwasher, then replacing this nut will ...
In Stock
This is a single rack roller kit for your dishwasher. This kit comes with one axel/clip, and one wheel/roller. The kit is used for the lower dishrack, and allows your rack to move freely. You will nee...
In Stock
Sold individually.
In Stock
$28.61
This is a basket for your dishwasher. It sits in the lower dishrack and holds small utensils during a washing cycle. This basket has six smaller sections where you can separate your cutlery into speci...
In Stock
Sold individually.
Special Order
Sold individually.
In Stock
Sold individually.
In Stock
This part connects the drain hose to the sink.
Special Order
Sold individually.
In Stock
This electrically operated propeller causes water to flow through your dishwasher's pump. This impeller is located above the dishwasher's mascerator blade.
In Stock
Special Order

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for DP400PWD1

Viewing 3 of 3
Leaking
Fixed by these parts
Fixing
How to fix it
Not cleaning dishes properly
Fixed by these parts
Fixing Fixing
How to fix it
Lid or door won’t close
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Dennis from Tryon, NC
Parts Used:
154106202
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench (Adjustable)
Water leaking under the dishwasher
I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwa sher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.
77 of 84 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eric from Holly, MI
Parts Used:
154106202, 5300806833
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Water leaking from under dishwasher
Removed lower trim covers (2 Phillips screws) disconnected power supply at breaker box. Removed wire from heating element, removed (broken) brass nut, unclipped heating element and removed. Removed flat washers and replaced with new grommets. Kind of tricky getting them in there. Also had to lube them with silicone to get the element back through. Installed new brass nuts and installed wire connectors. Reset breaker and started diswasher to verify repair. No leaks, working just fine, reinstalled lower trim covers
13 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from New Orleans, LA
Parts Used:
154106202
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
Water leak underneath dishwasher
Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.
11 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!