Models > DWU2005DR1

DWU2005DR1 Kelvinator Dishwasher

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for DWU2005DR1

Viewing 7 of 7
Keep searches simple, eg. "belt" or "pump".
This heating element mounting nut is used in dishwashers and is used to hold the nut to prevent leaking. If your nut is damaged or you notice leaking from the dishwasher, then replacing this nut will ...
In Stock
$28.61
This is a basket for your dishwasher. It sits in the lower dishrack and holds small utensils during a washing cycle. This basket has six smaller sections where you can separate your cutlery into speci...
In Stock
Sold individually.
Special Order
$14.92
This multi-use screw fits various appliances and tools such as, freezers, refrigerators, wall ovens, washers, ranges, dishwashers, dryers, microwave oven combos, combos, wine and beverage coolers. *Pl...
In Stock
It provides a seal between the tub and the door.
No Longer Available
Special Order
No Longer Available
Special Order
This rack roller is meant for usage with the lower rack of your dishwasher. It is white and just over an inch in diameter. The support for this roller is available separately. Use this roller with you...
Special Order
$87.47
Special Order
No Longer Available
No Longer Available

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for DWU2005DR1

Viewing 1 of 1
Leaking
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Dennis from Tryon, NC
Parts Used:
154106202
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench (Adjustable)
Water leaking under the dishwasher
I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwa sher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.
77 of 84 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eric from Holly, MI
Parts Used:
154106202, 5300806833
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Water leaking from under dishwasher
Removed lower trim covers (2 Phillips screws) disconnected power supply at breaker box. Removed wire from heating element, removed (broken) brass nut, unclipped heating element and removed. Removed flat washers and replaced with new grommets. Kind of tricky getting them in there. Also had to lube them with silicone to get the element back through. Installed new brass nuts and installed wire connectors. Reset breaker and started diswasher to verify repair. No leaks, working just fine, reinstalled lower trim covers
13 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jack from Soddy Daisy, TN
Parts Used:
5308016252
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Leaked Water
First I removed the old seal and comparied it with the new one and they were the same.
Then my wife put the new seal on. I helped her on the corners, very little. She did a very good job and it does not leak now.
15 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!