Models > HDA3500N20WW

HDA3500N20WW Hotpoint Dishwasher

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for HDA3500N20WW

Viewing 3 of 3

Manuals & Guides for HDA3500N20WW

Click to download
Keep searches simple, eg. "belt" or "pump".
The wheels on the lower rack of your dishwasher allow for the rack to slide in and out smoothly. If this is not happening, it may be necessary to replace one or more of the wheels. This kit includes 8...
In Stock
The rack slide end cap attaches to the rails of the upper dishrack, to prevent it from sliding all the way out. It is a one-inch white plastic part that can break over time. This might be the part you...
In Stock
If the upper rack in your dishwasher is not sliding in and out properly, the rollers may need to be replaced. Faulty rollers can also cause your rack to fall off the track, the door may not close prop...
In Stock
The corner tub baffle is made of black plastic, and is used to prevent water from leaking out of the dishwasher while it is operating. This genuine OEM part is for the lower right-hand side of your di...
In Stock
This is a genuine OEM corner tub baffle for the lower left-hand side of your dishwasher. It is made of black plastic, and is used to prevent water from leaking out of the dishwasher while it is operat...
In Stock
This is a manufacturer-approved lower dish rack with six wheels and supports. The lower dish rack is where dishes are placed in the bottom portion of the dishwasher to be cleaned during the wash cycle...
In Stock
This one piece dishwasher door gasket provides a water tight seal to keep water from leaking out of your dishwasher.
In Stock
This water inlet valve is an authentic OEM part for your dishwasher. If can be found behind the lower kickplate panel in either the left or right corner. The valve has a solenoid that opens or closes ...
In Stock
This interlock switch is a genuine OEM part that can be used in a variety of appliances like dishwashers and dryers. The switch is also known as a belt switch and works as a simple on and off mechanis...
In Stock
$13.82
This push on nut is for your dishwasher or refrigerator. As the name suggests, it pushes into place, rather than being screwed in. It is approximately half an inch in diameter and is made of stainless steel.
In Stock
The hinge link on your dishwasher connects the spring to the dishwasher door hinge. If the hinge link becomes cracked or damaged, you may not be able to shut or lock your dishwasher door properly. In ...
In Stock
This part helps keep the rinse aid the dispenser until its needed.
In Stock

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for HDA3500N20WW

Viewing 12 of 12
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Not cleaning dishes properly
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Not draining
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not dispense detergent
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door latch failure
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not drain
Fixed by these parts
Fixing
How to fix it
Door won’t close
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not fill with water
Fixed by these parts
Fixing Fixing
How to fix it
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Not drying dishes properly
Fixed by these parts
Fixing Fixing
How to fix it
Won’t Start
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Carl from Fairfield, TX
Parts Used:
WD12X10327
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
The rollers on the upper rack broke
There are eight guides that hold the rack rails in place. Use a Phillips screwdriver to remove the top two guides on each side in order to remove the rack from the dishwasher. The plastic axles on the rack and the rollers snap on. Use the hammer and punch to bend the metal clip on one end of the rail. Remove the plastic end piece the n slide the rollers out. Place two new rollers in the rail and put the plastic end piece on. Use the hammer and punch to bend the metal clip back into place. Snap the rails on the rack and set the rack on the guides in the dishwasher. Replace the top guide using the screwdriver, you will have to twist the rails in order get them in between the
guides.
544 of 571 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Huntingdon Valley, PA
Parts Used:
WD35X21038
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Lower rack wheel was melted
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.
520 of 542 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Teresa from Phenix City, AL
Parts Used:
WD35X21038
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The rear wheels were missing on the lower rack.
The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.
475 of 487 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!