Models
>
GLDT690D02BB
GLDT690D02BB General Electric Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for GLDT690D02BB
Viewing 4 of 4
Keep searches simple, eg. "belt" or "pump".
$13.21
The wheels on the racks in your dishwasher allow it to smoothly pull in and out of the appliance. If a wheel becomes broken or damaged due to regular wear or excessive force, it should be replaced so ...
In Stock
$16.44
This part holds the rinse aid liquid in the dispenser until the timer activates the rinse cycle.
In Stock
In Stock
$31.49
This part is the replacement tub gasket for your dishwasher. It is black in color and is made of rubber. The tub gasket fits around the circumference of your dishwasher tub, and creates a seal that pr...
In Stock
In Stock
In Stock
This door spring is approximately 7 inches long. The dishwasher door spring applies tension to the dishwasher door through the door hinge to prevent the door from dropping too quickly when the unit i...
No Longer Available
In Stock
$8.06
This is an official OEM approved replacement part for many GE Dishwashers, to see if this part will fit your appliance please see the "Model Cross Reference List" below. The Ring Nut with Gasket conne...
On Order
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for GLDT690D02BB
Viewing 6 of 6Leaking
Fixed by these parts
How to fix it
Not cleaning dishes properly
Fixed by these parts
How to fix it
Will not dispense detergent
Fixed by these parts
How to fix it
Not draining
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Christina from Canton, GA
- Parts Used:
- WD12X10231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels had come off and were broken
We ordered a whole new set for the lower rack and even though they were smaller than the original ones, we replaced them all and now the rack slides in and out of the dishwasher with ease!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Doon, IA
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cap was melted
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from VIERA, FL
- Parts Used:
- WD31X10114
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replaced inner door
I had to buy the inner door assembly since the seal at the bottom was not available separately. $104 for a $10 part.
Before you take anything apart, shut off the power. There is 110V in the door, and it’s pretty unforgiving.
The inner door assembly is manufactured with razor sharp edges all around. It is fastened w ... Read more ith approximately 11,000 Phillips screws, all of which fall under the dishwasher upon removal. The outer door will fall to the floor to indicate you have removed all the screws. Or, you could support the outer door, if you are smarter than I am.
Putting the new inner door on isn’t too bad. Mine was bent a little in shipping, but I bent it straight again, pretty much. I had my 19 year old son help hold it in place, so I could learn how “lame” this activity was. Once a couple of screws are installed, he can go back to sleeping 15 hours a day. Make sure the lower seal is aligned as you tighten the bottom screws.
Once you’re done, turn on the power and run the dishwasher. You’ll learn that the leak is due to a clogged discharge hose, and you just burned an hour an $104.
Before you take anything apart, shut off the power. There is 110V in the door, and it’s pretty unforgiving.
The inner door assembly is manufactured with razor sharp edges all around. It is fastened w ... Read more ith approximately 11,000 Phillips screws, all of which fall under the dishwasher upon removal. The outer door will fall to the floor to indicate you have removed all the screws. Or, you could support the outer door, if you are smarter than I am.
Putting the new inner door on isn’t too bad. Mine was bent a little in shipping, but I bent it straight again, pretty much. I had my 19 year old son help hold it in place, so I could learn how “lame” this activity was. Once a couple of screws are installed, he can go back to sleeping 15 hours a day. Make sure the lower seal is aligned as you tighten the bottom screws.
Once you’re done, turn on the power and run the dishwasher. You’ll learn that the leak is due to a clogged discharge hose, and you just burned an hour an $104.
Read less
Was this instruction helpful to you?
Thank you for voting!