DDT595SGJ0WW General Electric Dishwasher - Instructions

1. Turn off breaker supplying power to dishwasher in electrical panel
2. Open dishwasher door
3. Unscrew the screws that secure the dishwasher to the counter.
4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch.
5. On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside.
6. Remove old door latch.
7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in.
8. Plug wire harness into new door latch.
9. Re-align dishwasher and re-secure to counter in previous position.
10. Test latch to make sure it closes properly.
11. Turn on breaker in electrical panel.
The dishwasher should now function properly.

repair under warranty for Home Depot. Ordered new controller, new sump manifold, new piranh clamp kit, new diverter passive main assy, installation took 6 months. Could not finish as GE had changed the diverter to a new design with the same part number that the repairman had no knowledge of and there is no part available for the same configuration of the one that went bad, after I called GE tech line they were not aware of updates. Giving me the same numbers. The new design works if you order a new conduit main. As the old one in the dishwasher will not connect to the new Diverter. New deverter no. WD19X25278 and the new main conduit is the same as the old configuration no.WD12X21681 . The repair people and parts people are not yet aware of the design change and availability of parts, as most are out of stock and no updated pictures of the new design. Repair warranty washed their hands of this and Home Depot after 6 months gave me credit of my full price I bought this for 3 yrs ago. Repairing myself and sell.

Unplugged the dishwasher and turned off the water. In order to pull the dishwasher out I had to remove disconnect the waterline. Opened the dishwasher door to remove the screws attached under the counter holding the dishwasher in place. Once removed I pulled the dishwasher out of the under counter pocket far enough that I could access the rear connections to the heating element. Carefully disconnected the wires connected to the heating element and then loosened the large nuts securing the heating element. Once the nuts were removed I disengaged the element from the holders and removed it from the dishwasher. Installed the new element in place engaging it into the holders inside the dishwasher. Then moved back to the rear of the dishwasher installing the nuts that were removed earlier on the new element and reconnected the cables.

I ordered my new heating element prior to checking the continuity of the old one. I checked the continuity of the old one once it was removed and it was ok, not great but still acceptable so I knew the new element wasn't going to fix the issue, but installed it anyways. My issue was actually the float switch, so if you want to be sure of your issue, remove the current heating element from your dishwasher and check the continuity before ordering if you want to save some money.

Parts Select has excellent video instruction. they are way better than I could describe. the repair went smoothly. the heating element wasn't the issue. and it's may not be yours either. I found that the flood switch was the problem part number PS8690623. It's located under the filter screen in the bottom Yes that long grey plastic thing under the screen. It's held in by two 1/4 inch screws. Use a wet dry vacuum or towels to dry up the water in the sump. ABOVE ALL don't drop the screws. You'll be taking the pump apart if you do. Gently lift out the flood switch. There will be wires plugged into the base. With a flat screwdriver gently pop off the white plug from the green base. The plug only goes on one way reassemble in reverse order.

When the part arrived, I was pretty sure it was the wrong part. The replacement part had an LED on it -- a box that stuck up about an inch above the circuit board. My dishwasher did not have an LED readout and I was pretty sure the LED would not fit in the space that was available. I was reluctant to take the dishwasher apart until I had the right part. The people at Part Select were helpful and together we looked at the schematic which did, indeed, seem to show a box sticking up from the circuit board. A YouTube video showed me how to take the door off its hinges, unscrew 4 screws and slide the inside of the door upwards. The circuit board went in fairly easily. There was space for the LED (even though it still doesn't show through the top) and now the lights work.

Followed directions available on YouTube and the written instructions that came with the part. I made the repair more complicated than necessary as I did not notice that the jumpers come attached only to ONE pin out of the box. I took two tries to get the jumper settings right.

We bought this GE dishwasher new. After 9 months, we started noticing the dishes were not cleaning well. Eventually, the machine just filled up with water and drained. The washing arms didn't work. I replaced fill valve, but that didn't solve it. A GE Tech ran a diagnostic and informed us the pump motor was bad. It was off warranty and repairs would be $300. However, he noted it was easy to do on my own. Two pipe clamps. The part from PartsSelect was 40% less than ordering from GE and was a GE part. Replacement took half an hour and that includes getting it wrong once (one connection leaked due to a bad job attaching the pipe clamp). Works like a champ now.

I watched the video on how to replace the parts and it was very easy. Unplug the power cord, remove the kick plate and insulation. Remove the small square metal cover, remove the 2 screws that hold the control board plate. Unplug the wires, put the control board plate on the counter and replace the board. Then put everything back in the order that you removed it. Plug in the power cord. Very easy to fix. I ordered the door latch but didn't need it so I will just keep it as a spare. It took me less than 45 minutes to replace the part. The problem was the control board. Parts select saved me about 400.00. Thanks, John.

just bolted on the new one and hooked up the hose

Took old valve assembly off and replaced with new assenbly

Repair went fine, getting the right pump was the problem. I started with my local appliance parts house, they ordered part came in 3 days. Upon picking it up I noticed that the pump was shaped slightly different and the electrical hook up was totally different. Asking the parts guy what happened he said they must have sent the wrong pump. Returned it for credit and ordered it again. Four days later the same exact thing occurs. Parts guy credits my account and says better go directly to GE. Wait 10 days for GE, for this part and once again same odd looking pump with wrong electrical plug. My son who is a welder by trade asks me if there is a packet of parts in carton and yes there is. He says that perhaps there is a converter for the electrical. That was the solution no one told us that pump was universal and needed the adapter. Not even the 2 different tecks at first house. Perhaps that should be stated in the part would have saved us tons of time. Thanks D

I checked all the drain lines and filter for blockage. All looked good. I unplugged the unit and unscrewed the two screws adhereing the dishwasker to the counter. I shopvacced the water out of the bottom of the unit, slid it out, and carefully placed it on its back to access the pump. I unplugged the power to the pump, removed the intake and outake ring fasteners. Carefully removed the pump and inserted the new part, mopping up water as I went. Replace the rings, plugged in power to the pump, righted the unit and put it back. Replaced filter with the one that came with the kit.

I got lucky and found the diagnostic test instructions tucked inside the washer under the kick plate. From there I ran the tests on each component until I narrowed it down to the pump. The pump cost me less than local dealers. The install went well. Watched the online videos to make sure I was doing it right. Was actually very easy and saved hundreds over a service call.

The installation is fairly straightforward, basically one plug in electrical connection and two plumbing connections. The smaller of the two plumbing connections can be tricky because of the hose clamp... The original clamps are one time use crimp style. The replacements are standard hose clamps, which means the section where the tension mechanism is, is a bit wider than the clamp itself... This can cause the rubber collar on the dishwasher to slide off/separate from the pump part itself when tightening the hose clamp. If you are careful and align things just right, it will work like a charm. The best advice I have is to take your time and make sure the connections are snug without being too tight, otherwise it could leak and/or something else could break.

Started by removing dishwasher, including disconnecting power, water and drain line. Then turned washer on back. Electrical connector to old wash pump was a little tricky to remove as the release tab isn’t straightforward, I used a tiny screwdriver and jiggled it around till it came loose. The factory hose clamps (2) are crimped on, but if you can find the tail end you can work them loose with a screwdriver by prying the tail up from the body of the clamp. Once you have the electrical connector and the two clamps removed, the pump comes of easily with a twisting motion. The new wash motor came with new clamps (2 extra). When sliding the rubber boots on the new pump in place, it will require a twisting motion to position it correctly, make sure (I didn’t and had to go through the whole process twice) that the rubber boot is not folded under on the bottom where it’s hard to see. Tighten clamps carefully and don’t over tighten. Plug in electrical connector and you’re ready to reinstall dishwasher.