Models
>
PDW8000G01BB
PDW8000G01BB General Electric Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for PDW8000G01BB
Viewing 4 of 4
Manuals & Guides for PDW8000G01BB
Click to downloadKeep searches simple, eg. "belt" or "pump".
$43.21
This water inlet valve is an authentic OEM part for your dishwasher. If can be found behind the lower kickplate panel in either the left or right corner. The valve has a solenoid that opens or closes ...
In Stock
Order now and your part arrives by Mar 26
This wheel is sold individually. It comes with an attached axle.
No Longer Available
In Stock
Order now and your part arrives by Mar 26
Special Order
These clips are sold in a pair. They are used in conjunction with the front and rear inserts for the lower dishrack.
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for PDW8000G01BB
Viewing 4 of 4Leaking
Fixed by these parts
How to fix it
Will not fill with water
Fixed by these parts
How to fix it
Not cleaning dishes properly
Fixed by these parts
How to fix it
Not draining
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Greg from Burlington, VT
- Parts Used:
- WD15X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Water leak, small puddle to front left of dishwasher
You'll need to remove the front toe kick and (if installed, the GE Profile baffling for additional silencing action).
You will need to disconnect the right wire connection to access the right screw (and may need to use a flat head screwdriver). You can then remove the 2 screws that hold the Valve Water Inlet on.
... Read more >You will then need to loosen and the hose clamp that attaches the water line to the Valve Water Inlet. You may need to force it undone since the rubber connection is pretty secure around the water tube inlet.
Disconnect the plastic wire housing from the Valve Water Inlet and you should now have the Valve Water Inlet disconnected.
Reverse the order and reconnect everything and you should be good to go!
Double-check for any leaks prior to pushing everything back in :)
You will need to disconnect the right wire connection to access the right screw (and may need to use a flat head screwdriver). You can then remove the 2 screws that hold the Valve Water Inlet on.
... Read more >You will then need to loosen and the hose clamp that attaches the water line to the Valve Water Inlet. You may need to force it undone since the rubber connection is pretty secure around the water tube inlet.
Disconnect the plastic wire housing from the Valve Water Inlet and you should now have the Valve Water Inlet disconnected.
Reverse the order and reconnect everything and you should be good to go!
Double-check for any leaks prior to pushing everything back in :)
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J from Walnut, CA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Leaking water when in use.
Part was an exact match. Make sure to use plumber's tape on all threads. Had to really tighten fittings to prevent leaks. Screws are a little difficult to get to. Test for leaks first, before final installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Grand Isle, VT
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher was leaking.
Removed the wire clip, then removed two screws on mounting bracket. Then disconected the hose. Removed the brass elbow.
Then reversed these steps and I was done.
Then reversed these steps and I was done.
Was this instruction helpful to you?
Thank you for voting!