GDF510PGR6BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Teri from LAGUNA NIGUEL, CA
- Parts Used:
- WD01X35298, WD12X26146, WD28X34744, WD01X35298, WD01X35298, WD01X35298
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
order #16343054 Complete service rack
this was ordered 4-9-21 and I have yet to receive it. Its difficult to explain the installation when you haven't received the main part. I paid for this but you have not shipped it. Very poor customer service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark De from BRONX, NY
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Spray arm had become unattached and burned by the heat element
It was a simple as: attach and done!
There is a ring on the part that tightens clockwise to the nipple that sprays out the water that it rests on. Twist clockwise and you are done!
It is a mystery how it was unattached to begin with but not a problem in the end, it was easy to fix!
Thanks for sending genuine GE parts!
There is a ring on the part that tightens clockwise to the nipple that sprays out the water that it rests on. Twist clockwise and you are done!
It is a mystery how it was unattached to begin with but not a problem in the end, it was easy to fix!
Thanks for sending genuine GE parts!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Waldorf, MD
- Parts Used:
- WD08X27458
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
A slow drip from the pump area.
Replaced floating seal. Un plugged and Pulled washer out from the counter and laid on its left side. Pull pump out of seal by hand. Straight screwdriver to lever seal out of fitting. Clean hole and wipe seal then push into hole. Reinsert pump reverse install.
To make it easier I previously extended the water supply hose to nearly 8 feet so did not have to disconnect it.
To make it easier I previously extended the water supply hose to nearly 8 feet so did not have to disconnect it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from OAKDALE, PA
- Parts Used:
- WD28X34744
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
The service rack vinyl coating had worn off on the rails on the bottom resulting in the metal being exposed and rusted.
Could not do the repair. The incorrect service rack was shipped. It was a different model than what was ordered. It was a different size and would not fit. Had to ship it back at my own expense. Service rack was $77.03 and that has been reimbursed. The return shipping cost to me was $43.75. That expense still has not been reimbursed. I do not want to risk ordering another service rack and risk having to go through the same type of service again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from CICERO, IN
- Parts Used:
- WD01X35298, WD12X26146
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Roller carrier got melted by heat coil
Replaced bad roller carrier with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cooke, from STAMFORD, CT
- Parts Used:
- WD28X34744, WD28X35779
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Racks were rusted
Terrible! Bottom rack was wrong... original was discontinued. Fork and knife holder did not fit in original location. Parts company new this and still processed the order! Disaster!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kyle from WALLINGFORD, CT
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original spray arm got stuck under lower heater element and melted.
Removed old spray arm. Installed new one. New model spray arm doesn’t need metal heat shields.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy from CHESAPEAKE, VA
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replaced Lower Spray Arm for GE Dishwasher
There was no repair -- it was a simple snap-in replacement of lower spray arm assembly. The shaft holding the lower spray arm in place is plastic so of course it broke when a utensil blocked the arm from spinning.
I appreciate the Parts Select company for enabling me to purchase a replacement part though that allows me to keep my old dishwasher working.
I appreciate the Parts Select company for enabling me to purchase a replacement part though that allows me to keep my old dishwasher working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from ANKENY, IA
- Parts Used:
- WD28X35779, WD28X34744
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original dishwasher racks. Both top and bottom had several prongs rust and break off. Leaving half the racks useless.
Ordered both a top and bottom rack. It's as simple as pulling the old ones out and sliding the new ones in. There's two small clips for the tops rack that need opened and placed the new rack. As well as the plastic blade. No tools were needed for any of it. Would highly recommend these as replacements if someone needs them. Couldn't be any easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from STATEN ISLAND, NY
- Parts Used:
- WD08X23476
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
tub gasket was damaged
damage to gasket (had a slit in the area of the utensii baskets.
causing lower right corner of gasket to come out. caused leakage to floor from the lower right corner of door...
As I am 77 yrs of age I was leary of diy but thanks to the reps of
"Parts Select" I actually was able to put in the new gasket myself.It did take some time and lots of patience as it had to be seated correctly..I also had to make sure the new gasket was in the groove as it is supposed to be.
causing lower right corner of gasket to come out. caused leakage to floor from the lower right corner of door...
As I am 77 yrs of age I was leary of diy but thanks to the reps of
"Parts Select" I actually was able to put in the new gasket myself.It did take some time and lots of patience as it had to be seated correctly..I also had to make sure the new gasket was in the groove as it is supposed to be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from HAMBURG, PA
- Parts Used:
- WD08X23476
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bad tub gasket
Thanks to this site for saving me about 150.00.This is my third repair with parts from your company. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Montgomery from DELAFIELD, WI
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Loud knocking. Sounds like plate banging against other plates or side of dish washer.
1) Pull out lower basket plate holder out. Now would be a good time to check roller wheels. 2) Grasp lower spray arm base (knurled collar on base) and turn counter clockwise to release. 3) Install new spray arm and turn knurled collar on base clockwise to lock it in. 4) Reinstall lower basket plate holder.
* Done *
* Done *
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rickey from POPLAR BLUFF, MO
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower spray arm broke
Opened the door, put arm on bottom, slid in and twisted. Very, very easy. The right part means a lot. Thank you very much. “ Ol Stump”.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from COLORADO SPGS, CO
- Parts Used:
- WD28X34744, WD28X35779
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Both our dishwasher racks rusted and the pegs broke off of our 5 year old dishwasher.
All we had to do was order the top and lower racks and put them in. It was way less work and cheaper than having to put in a new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Rio Verde, AZ
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower arm spray had hole melted in it
Simply put it on and twist it to lock in place. Took all of 3 seconds
Was this instruction helpful to you?
Thank you for voting!