Models
>
CDT845M5N8S5
CDT845M5N8S5 General Electric Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for CDT845M5N8S5
Viewing 10 of 10Keep searches simple, eg. "belt" or "pump".
$13.13
The roller helps the lower rack of your dishwasher to smoothly slide in and out of your appliance. A broken or worn roller wheel can make it clunky or difficult to get the rack in and out of the dishw...
In Stock
In Stock
In Stock
This part is a replacement middle spray arm bearing for your dishwasher. The spray arm bearing reduces friction and allows the spray arm to rotate during the operating cycle. If the spray arm is not r...
In Stock
$8.06
This is a genuine GE dishwasher leveling screw. It operates as a leg on the bottom of your dishwasher, and can be screwed in and out to raise and lower the height of the dishwasher. It is made of meta...
In Stock
$8.06
This dishwasher latch strike is a manufacturer-approved replacement part for your appliance. The latch strike is an important component in your dishwasher door assembly, and adds an extra layer of sec...
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for CDT845M5N8S5
Viewing 8 of 8Leaking
Fixed by these parts
How to fix it
Not cleaning dishes properly
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Not draining
Fixed by these parts
How to fix it
Will not fill with water
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edward from LOUISVILLE, KY
- Parts Used:
- WD12X23557, WD08X10092
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Dishwasher leaked because vent cover would not stay on
Replaced transition piece, gasket, and vent cover. The root cause problem is that the factory installed gasket was too thick and would not allow sufficient thread engagement. The replacement gasket was about 25% thinner and worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Waldorf, MD
- Parts Used:
- WD08X27458
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
A slow drip from the pump area.
Replaced floating seal. Un plugged and Pulled washer out from the counter and laid on its left side. Pull pump out of seal by hand. Straight screwdriver to lever seal out of fitting. Clean hole and wipe seal then push into hole. Reinsert pump reverse install.
To make it easier I previously extended the water supply hose to nearly 8 ... Read more feet so did not have to disconnect it.
To make it easier I previously extended the water supply hose to nearly 8 ... Read more feet so did not have to disconnect it.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from CONNEAUT, OH
- Parts Used:
- WD22X20688
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the hub that holds the spinner for the top water in the dishwasher broke
the design of this part is easy to break when closing the top rack.
there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher
the part broke when closing the rack [a dish too tall hit it]
it took less than 5 minutes to replace as ... Read more the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel
there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher
the part broke when closing the rack [a dish too tall hit it]
it took less than 5 minutes to replace as ... Read more the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel
Read less
Was this instruction helpful to you?
Thank you for voting!