Models > GDF630PGM1WW

GDF630PGM1WW General Electric Dishwasher

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for GDF630PGM1WW

Viewing 7 of 7
Keep searches simple, eg. "belt" or "pump".
The roller helps the lower rack of your dishwasher to smoothly slide in and out of your appliance. A broken or worn roller wheel can make it clunky or difficult to get the rack in and out of the dishw...
In Stock
$8.56
This is a genuine OEM replacement gasket for your dishwasher, that measures approximately 22 inches long and is made of plastic. It is found at the bottom of the inside panel of your dishwasher door. ...
In Stock
$44.31
If your dishwasher door will not close or latch, or the machine will not start, you may need to replace the door latch. This genuine OEM replacement latch is meant to keep your dishwasher door closed ...
In Stock
This is an authentic lower dishrack with wheels. Please note that the manufacturer has made a design change, which requires the silverware basket to be relocated from the door to the inside of the rac...
In Stock
If your dishwasher is leaking water while it is running, there may be an issue with the gasket. Also known as a door gasket, the tub gasket creates a watertight seal between the tub of the dishwasher ...
In Stock
$14.31
This genuine OEM part is an end cap for the racks in your dishwasher. The end cap ensures that the rack does not fall off the rails when you pull the rack in and out. If the end caps are damaged or mi...
In Stock
This genuine OEM bracket is used to secure the dishwasher to your cabinetry. The mounting bracket measures approximately 3 inches in length and is made of metal. If you have a solid-surface countertop...
In Stock
This is a washer inlet valve assembly for your dishwasher. This valve allows water to flow into your dishwasher at the proper rate. If your dishwasher tub is not filling with water or filling when the...
In Stock
Sold Individually.
In Stock
This kit includes the lower and middle spray arms. Water is forced through this spray arm by the unit's pump and motor assembly. The force of the water propels the spray arms, spraying water and deter...
No Longer Available
The detergent dispenser in your dishwasher stores the detergent until it is ready to be dispensed. If your dishes are not coming clean, or you notice the detergent is still in the dispenser at the end...
In Stock
This part is the replacement carrier roller for your dishwasher. It is also known as the wheel support. It is made of gray plastic and is approximately 5 inches by 2 inches. The carrier roller support...
In Stock

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for GDF630PGM1WW

Viewing 10 of 10
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Not cleaning dishes properly
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door latch failure
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not fill with water
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Not draining
Fixed by these parts
Fixing Fixing
How to fix it
Will not dispense detergent
Fixed by these parts
Fixing
How to fix it
Not drying dishes properly
Fixed by these parts
Fixing Fixing
How to fix it
Door won’t close
Fixed by these parts
Fixing Fixing
How to fix it
Noisy
Fixed by these parts
Fixing Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
D from LE CENTER, MN
Parts Used:
WD08X21894
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Gasket at the bottom of the door disintegrated.
Took off the kickplate, diconnected the wires and removed the whole door by lifting straight up, removing spring wires from hinges. Once door is disconnected from the machine, removed one hinge by removing bolt. Slid gasket into place, secured hinge back in place, then reconnected wires at bottom, replaced hinge spring wires and slid d oor back down onto hinges. Now that we know how to do it, could do it in 15 min to half hour.
39 of 54 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from ALBRIGHTSVLLE, PA
Parts Used:
WD21X10490
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Door latch not functioning
1. Turn off breaker supplying power to dishwasher in electrical panel
2. Open dishwasher door
3. Unscrew the screws that secure the dishwasher to the counter.
4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch.
5. On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside.
6. Remove old door latch.
7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in.
8. Plug wire harness into new door latch.
9. Re-align dishwasher and re-secure to counter in previous position.
10. Test latch to make sure it closes properly.
11. Turn on breaker in electrical panel.
The dishwasher should now function properly.
25 of 39 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Teri from LAGUNA NIGUEL, CA
Parts Used:
WD28X27241, WD12X26146, WD28X26099, WD28X27241, WD28X27241, WD28X27241
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
order #16343054 Complete service rack
this was ordered 4-9-21 and I have yet to receive it. Its difficult to explain the installation when you haven't received the main part. I paid for this but you have not shipped it. Very poor customer service.
20 of 28 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!