GDPP4517AF1B Frigidaire Dishwasher - Instructions

Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new.

I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.

I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwasher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.

My friend bought a used dishwasher at a garage sale, the previous owner had thrown away the drain hose because it was "nasty" they said....remember it could have been cleaned. When I went to install it, I removed the old washer, and discovered that the old hose would not fit on the replacement dishwasher. I went to the local repair shop, armed with the model and serial #'s. they searched and searched their books and could not find the hose part number. they said "good luck" when I left...I went home and looked up the model on your web site, ordered the hose, and in 3 days had the dishwasher installed and running in about 30 minutes...thanks for prompt shipping.. I couldn't believe it arrived so soon...Mowerman

Pulled out the dishwasher - Located the vent assembly part - unpluged the wiring harness - installed new vent on top of washer plugged in the harness - disconnected the water supply as I had to adjust the rear left leg. Once done I reconnected the water supply and repositioned the dishwasher. WA-LA once installed problem solved.No more washing by hand.

Removed bottom plate and heating element brass nuts. Disconnected heating element. Connected new one then replaced brass nuts. Put bottom plate back on. Very easy.

removed the remnants of the old wheels and popped the new ones on....simple

Got to say, I was pretty amazed that I received my order the following day! You guys are wonderful!

Alighned the bracket and pushed in.

It would sometimes work, which led me to believe it was a switch. Looked on line and found the mail switch to go on was in the latch. I took it apart, 6 screws, wiggled the switch and it went on. So I found the door switch to be bad. It was very simple to change the switch.

Probably the easiest repair job that you could encounter. I removed the old gasket from the door frame. Cut the new gasket to length and pushed it into the door frame.

Water leak solved...

After figuring out the problem wasn't the water inlet switch, I replaced the switch assembly for the water level float. Cut off supply water to dishwasher, removed the 2 screws holding switch assembly, and installed new switch. 15 minutes, very easy job.

Broken friction cable on the right hand side. Remove screws that hold dishwasher to cabinet, pull out the dishwasher far enough to get to the friction cable and rear spring. Remove broken cable. Attach new cable to rear spring and connect to door hinge. Push back dishwasher and screw in the two screws that keep the dishwasher attached to the cabinet. Very simple.

First thing I did was turn off the power to the dishwasher, then remove the racks. Remove the foot plates, remove the two top screws holding the dishwasher. Then using the socket set, retract the two foot stands to pull the dishwasher forward. You may not have to do this step as I had to get it over tile. The pully springs are on the sides, easily replaced. After replacing the springs and I recommend replacing both at the same time, put everything back. The hardest part will be the foot plates, there are two and getting them lined up and the screws back in is a bit of a challenge. Then you are done.

The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job

I had to remove the dishwasher from under the counter, flip it on it's side to gain access to the discharge hose attachment point, removeit, remove the other end of the hose from the sink-side and replace the hose. The sink-end of the hose has a 'collar' that must be cut to fit the fitting on the sink.