SHE3AR72UC Bosch Dishwasher - Instructions

We let this go for a shameful amount of time before I decided I could probably fix it. The roller broke so you could only pull it out about halfway or it would come off the track. I looked up the part, and bought it. Actually bought two in case it happened again. When I arrived I looked at how it was put together on the other side and then just basically pushed it onto the rod and it was fixed. I am ashamed it took so long to do it. Never be afraid to try it yourself. It was a total of $10 shipped to fix it.

pushed with thumb pressure and snapped rollers into place.....EASY

This was the third time I replaced a fill valve in a Bosch diswasher, twice in this unit and once in a previous unit. I read the installation hints on your web site and want to add the following suggestion.

The notes on your web site say you can remove the valve from behind the toe face and pull it out to reach the hose and plug. I found that the Bosch designers called for both the hose and wire to on the short side. I found that pulling the dishwasher forward 6" to 9" allows you to access these connections from the side at least to hold them while making the connection. I hope this helps. Thank you, Bill

Turn off water, disconnect power cord, remove front kickplate. Remove 2 screws that hold the water inlet valve, pull it out, disconnect electrical connection, disconnect water supply.. Check the inlet valve with volt-ohm meter for continuity. If it is good, then the valve is stuck shut. The ohm reading should be in the 900-1100 range. Replace valve, installation is the reverse.

disconnected inlet hose and water line from sink, removed old inlet valve and installed new valve and reconnected inlet hose and water line from sink - checked for leaks.

replacing the sensor was simple, just unplug and turn it out, but didn't solve the problem, it's a float sensor that doesn't show up on the tech sheet in the dishwasher or anywhere in troubleshooting on the internet I could find.

Remove the dishwasher from under the counter. Remove door springs. On the inside of the lip of the door remove the 6 screws that hold the outer door panel on, and remove panel. this will expose hinge screws. Remove the two screws per side holding the inner door to the hinge assembly. Take pictures of the way the gasket's grey plastic end cap assembles between the inner door frame and the hinge, and remove the inner door. The old gasket has a channel lip that sits on the plastic edge of the washer tub, pull it off this lip and discard. Install new gasket and put it all back together! Use this opportunity to clean the gunk out of the upper door seals.

I watch utube to assess the problem then took eveything apart and saw the build up on the filter, which i had never cleaned. I tried to clean it but was unsuccessful so order the filter from partselect and it came within a couple of days, installed very easily and began to clean as it always had.

Replacement was fast and very simple. Was completed in less than 5 minutes.

easy repair, but the check valve wasn't the problem, it was the float switch that isn't on the tech sheet in the dishwasher or mentioned as a possible culprit anywhere I could find on the internet

Slip the wheel onto the axle, snap the clip facing up onto the frame

There were 5 rollers still in place so I used them to show me how to snap the replacement roller in place.

Followed instructions from YouTube.

This repair was relatively easy and saved us literally hundreds of dollars as well as time...we were looking at 3+ weeks for a technician to come out. And that was just to diagnose. The hardest part was my own lack of experience and getting the dishwasher out because of a poor installation. The best part was identifying and ordering the part from PartSelect. The part came quickly...within 2 days. I had ordered a wrong part previously and they took it back no problem. Very pleased with the whole process and their help videos.

Removed the dishwasher from the cabinet, laid it on its side, removed the old pump/heater, installed the new and reinstalled the dishwasher. What made this a little more difficult is my dishwasher has a bottom to it that would be very difficult to remove, access to the pump is from the side! I have large hands, not much room to work!