SHE68T55UC (07) Bosch Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Raymond from VIENNA, VA
- Parts Used:
- 10023852
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
E:15 error code with Watertap
The E:15 error code means water is detected in the pan under the unit. There are several ways this can happen.
In this case, it was caused by a bad inlet valve. It did not close properly and led to an overflow of water inside that eventually spilled into the pan underneath the unit.
I see now why the pump keeps running after this error. In this case, it would have led to a big flood in the kitchen if it did not.
I was actually able to run the unit while broke by manually operating the valve under our sink that provides water to the unit.
Be sure to turn off breaker before servicing. Don't get shocked!
Be sure to turn off water before starting! Or, you'll have a flood.
Anyway, I just pulled the unit out (was secured by 2 screws on the sides). I lifted up the insulation material on the left side to get at the valve. Pushed a little green tab to release the electrical plug. Then, use pliers to move clamp off the white water hose on the inside. Then, pull of white hose. This was hard in my case. Took a lot of force. Then, reach behind the unit and use pliers to unscrew water hose. Now, the whole gray panel there can pop out with some force. Then, slip the old valve out and slip new one in. Reconnect hoses and clamp. Note that I put some caulk on the connector where white hose goes. Not sure if needed or not.
Good luck!
In this case, it was caused by a bad inlet valve. It did not close properly and led to an overflow of water inside that eventually spilled into the pan underneath the unit.
I see now why the pump keeps running after this error. In this case, it would have led to a big flood in the kitchen if it did not.
I was actually able to run the unit while broke by manually operating the valve under our sink that provides water to the unit.
Be sure to turn off breaker before servicing. Don't get shocked!
Be sure to turn off water before starting! Or, you'll have a flood.
Anyway, I just pulled the unit out (was secured by 2 screws on the sides). I lifted up the insulation material on the left side to get at the valve. Pushed a little green tab to release the electrical plug. Then, use pliers to move clamp off the white water hose on the inside. Then, pull of white hose. This was hard in my case. Took a lot of force. Then, reach behind the unit and use pliers to unscrew water hose. Now, the whole gray panel there can pop out with some force. Then, slip the old valve out and slip new one in. Reconnect hoses and clamp. Note that I put some caulk on the connector where white hose goes. Not sure if needed or not.
Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from PLEASANTVILLE, NJ
- Parts Used:
- 00611475
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
rollers broke
pushed with thumb pressure and snapped rollers into place.....EASY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from MIDDLEBURY, VT
- Parts Used:
- 00779033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The middle rack was rusting and some of the pegs were coming off.
Removed the spray arm, front handle, and little clips from the old rack and installed onto the new rack. Was very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from DALLAS, TX
- Parts Used:
- 20000533
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
A prong in the bottom rack had broken nearly through where it attached to the base & was rusting severely. Several other prongs had also started to rust.
The bottom rack of our Bosch dishwasher was discontinued & no longer available anywhere, so we ordered an OEM replacement rack from PartSelect.com & hoped that it would fit.
The new rack fits perfectly & is actually an improvement over the old one. The new rack doesn't have a vase tower, but that is actually a big design improvement because it can store more dishes & is more flexible than the old one. The new rack comes without a handle cover, but it was very easy to move the handle cover from our old rack to the new one.
The new rack fits perfectly & is actually an improvement over the old one. The new rack doesn't have a vase tower, but that is actually a big design improvement because it can store more dishes & is more flexible than the old one. The new rack comes without a handle cover, but it was very easy to move the handle cover from our old rack to the new one.
Was this instruction helpful to you?
Thank you for voting!
Lower tines rusted out and would not hold dishes to clean them properly.
Removed two rusted tines lines, then I unclipped the stabilizers, installed four other positioning clips, put the two adjustable tines in the two vertical plastic stabilizers at the ends of the lower baskets. Worked like a charm and all is good. May I suggest using stainless steel or more nickel in the iron used in the basket or a thicker or more durable plastic in the tines.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KATHLEEN from PECONIC, NY
- Parts Used:
- 10023852
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
E15 code basin filling up with water
Turned off electric
Slid out unit - the water connection on this model is in the back
Disconnected the H2O hose. This valve access part is the part that connects the dishwasher to the H2O supply. The soon to be replaced part had sediment in it preventing H2O to go into the dishwasher and into the basin instead. The exploded view of dishwasher was a big help. It was a guess as to why this was happening. Now that I’ve had it apart it makes sense that this is the part that would fail after a period of time, especially if you have city H2O. My husband Bob did this repair.
Slid out unit - the water connection on this model is in the back
Disconnected the H2O hose. This valve access part is the part that connects the dishwasher to the H2O supply. The soon to be replaced part had sediment in it preventing H2O to go into the dishwasher and into the basin instead. The exploded view of dishwasher was a big help. It was a guess as to why this was happening. Now that I’ve had it apart it makes sense that this is the part that would fail after a period of time, especially if you have city H2O. My husband Bob did this repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from OVERLAND PARK, KS
- Parts Used:
- 00779033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Replace top rack
Removed old rack and several accessory pieces, and installed them on the new rack. Slid the new rack back in. Took about 15-20 minutes top. Very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from CLERMONT, FL
- Parts Used:
- 00494772
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Water leak on top of door.
Went to on line video and followed it. The old gasket came right out and the new one fit right in. Started at the top middle and worked the gasket in on both sides to make sure it was evenly spaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David E. Kolva, from OSWEGO, NY
- Parts Used:
- 00689412
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced door skin from factory black to new stainless steel
Unscrew 6 Torx screws and slip/slide down and off outer door panel. Take off old insulation and place it into interior of new door skin. Slide new sin into place and allow clips to engage to snug. Retighten 6 Torx screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from STURGEON BAY, WI
- Parts Used:
- 00611475
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
There was a roller missing from the lower washing rack.
There were 5 rollers still in place so I used them to show me how to snap the replacement roller in place.
Was this instruction helpful to you?
Thank you for voting!
WATER DRAIN MATRIX became plugged with sludge, stopping ventilation for draining function
removed machine so left side water drain matrix was accessible, replaced that unit, reinstalled machine to its built-in location.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Safford, AZ
- Parts Used:
- 00645038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Poor cleaning of dishes and calcium build up on filter
I watch utube to assess the problem then took eveything apart and saw the build up on the filter, which i had never cleaned. I tried to clean it but was unsuccessful so order the filter from partselect and it came within a couple of days, installed very easily and began to clean as it always had.
Was this instruction helpful to you?
Thank you for voting!
The original plastic and rope in the closing mechanism broke and needed replacing.
Note: The diagram and part description misled me to think that each item was a quantity of one, so I ordered two since I wanted to replace the part on each side of the door. In fact, both the cable repair kit and the guide came with a quantity of two, so have an extra set that I will likely never need. As far as the replacement, it was quick and easy. The hardest part was pulling the dishwasher out from under the cabinet.
Was this instruction helpful to you?
Thank you for voting!
The washer had an error message in the display of E:09. I called Bosh on customer srevice and she said that the heat pump was not working and needed to be replaced. Since the motor is the main part for this that needed to be replaced as well. The pars were under $200.00 total so we oted to fix this
We followed the video and had no problems with leaks at all afterwards. The parts fit perfectly and the machine is working great again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from MADISON, CT
- Parts Used:
- 00745856
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dishwasher door would not close properly, spray arm would not engage plug
popped off old spray arm from under the rack and put on new spray arm,
couldn't be any easier, 5 minute job, door closes easily now!
couldn't be any easier, 5 minute job, door closes easily now!
Was this instruction helpful to you?
Thank you for voting!