SHY66C06UC-14 Bosch Dishwasher - Instructions

I used a wet vac to remove the water from the dishwasher. remove cover and filter/strainer from bottom of dishwasher. remove screw which allows you to lift the plastic piece to access check valve. Original check valve looked like new , I installed new check valve re installed parts . Job done and issue resolved .

There are two ways to do this repair: the "right" way and the hard way. I chose the hard way, as the right way involves disconnecting the dishwasher plumbing, removing the dishwasher from under the counter, taking all the outer panels off, and disabling the door springs. There are good YouTube videos on this. The hard way doesn't involve that -- but is not all that easy and I'm not sure I'd recommend it. The problem, in essence, is that to install the new seal there is now way to do it without taking the door off the machine and taking the door apart -- which requires that the springs be locked out, if not disabled.

I accomplished that part of it by opening the door, partially, undoing the two screws on each side which hold the hinges, taking the front panel off (piece of cake, with a Torx driver),slipping the door partly off the hinges, and then locking the hinges open with the pry bars.

There are an assortment of ways one could seriously damage either the door or one's self doing it that way -- the hinge springs are very powerful -- so I don't recommend my approach.

The old Tine holders used on the upper and lower dish rack dried up and cracked/broke. So I purchased new Tine holders for the upper and lower racks and snapped the new parts in place.

REMOVED DISHWASHER FROM CABINET. DETACHED BASE FROM BODY OF THE DISHWASHER. INSTALLED NEW CORD, REATTACHED BASE TO BODY OF DISHWASHER AND REINSTALLED IN CABINET. OPINION: THIS IS A LENGTHY REPAIR AND UNNECESSARY ONE. THE CORD IS PART OF THE DOOR COUNTERWEIGHT AND SUBJECT TO TENSION EVERY TIME THE DOOR IS OPENED, AS WELL AS POTENTIAL CHAFFING DUE TO PROXIMITY TO VARIOUS METAL PARTS, AND VIBRATION. THE CORD SHOULD BE MADE OF STRONGER MATERIAL AND ARMORED OR ALLOWED MORE CLEARANCE. BOSCH SHOULD FIX TO LAST THE LIFE OF THE DISHWASHER.

Turn off power to unit!
-Remove kick panel,2 screws.
-remove water valve, 2 screws, 3 electrical connections, 1 hose clamp.
-Remove elbow from old valve and install on the new valve ( use teflon pipe tape)
-replace valve, hose & hose clamp, electrical connectors and water supply line.
Scew unit in place ,2 screws.
Check for leaks then replace kick panel, 2 screws.

I removed the old gasket easily, it pulled right out. I spent a few minutes cleaning the gunk out from the seam using a standard kitchen cleaner (it was gross and I had to do it multiple times). Tip: pay attention to the shape of the gasket and which side faces in vs. out when pulling out the old one. Also, for reference, take a photo of the old gasket and how it's positioned before pulling it out. Then, simply start at the bottom (either side) and insert the new gasket. Work your way up, over and down the other side. If it's facing the right way it'll go in very easily, if not is will be very difficult—this is how you'll know. After installation, run your dishwasher empty for a full cycle (with towel underneath the door) and check back frequently during the cycle. If there are no leaks you're done. This was the fastest, easiest way to attempt to fix a leaky door and eliminate the gasket as the problem (which it did!) If the machine still leaks the issue is likely something bigger.

Went to on line video and followed it. The old gasket came right out and the new one fit right in. Started at the top middle and worked the gasket in on both sides to make sure it was evenly spaced.

To perform the repair, the door panel must be removed (8 Torx screws) and the door removed from the hinges in order to access the lower door seal. For this model Bosch and other similar models, the hinge springs must then be disengaged (safer) or kept from retracting. To disengage the springs requires removing the entire unit, disconnecting the water supply, and flipping it on its side to disengage the springs. I chose the latter, keeping the unit in place, holding the hinges with vice-grips on either side, then removing the door. This was not easy and caution is required. Either method is risky with a 20-year dishwasher.
The replacement part does not fit as well as the original (much sturdier) part, but appears to seal well for now. Repair videos on the internet are for different, newer models where disabling the hinges as described here is not required, making the repair much easier. Recommend looking carefully at your model/manual to determine if the difficulty of the repair is easy or hard.

Vice grip door hinges. No need to disconnect, un hook hing springs. Works slick. Small vice grips. On hinges. Remove tore screws. Remove seal , and replace seal, reconnect door screws. Boom done.

Dishwasher racks are maddening. It takes years to understand how to make your dishes fit within your dishwasher. We just moved and nothing was working so I did something that I did not want to do--pay attention to the lower rack and figure out why it had a mind of its own. Well, the Bosch interior is filled with adjustable (that usually means problems) fingers. Well, it was not so. A piece was missing that supported the "hand" from which the fingers sprang. That support piece cost about a buck and was available and ultimately on my doorstep in a day or three. Take the part out of the bag, snap it on the hand and enjoy dish racks that don't flop around. Awesome indeed.

Replaced parts

I took out the old filter and replaced it with the filter I had ordered. Very easy and not necessary to call a repairman.

Disconnected the water and power, pulled dishwasher out from under the counter, unscrewed the old inlet valve, disconnected hose from exit of inlet valve, noted the placement of the wires and disconnected them. Installed new inlet valve in reverse order and reinstalled dishwasher.

Followed the video on your site and it was an easy install with no more leakage.

I have granite countertops and one of the hold down brackets broke to wood cabinet side mount. Easy and fast repair to remove old brackets, pull out dishwasher, and I replaced both brackets with new, and new wood screws. New installation looks better than original done 18 years ago. Very easy to do and saved a lot of money if I had an appliance repair company do it.