SPE68B55UC/07 Bosch Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from AUBURN, IN
- Parts Used:
- 00611323
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dishwasher not draining, dishes dirty
replacing the sensor was simple, just unplug and turn it out, but didn't solve the problem, it's a float sensor that doesn't show up on the tech sheet in the dishwasher or anywhere in troubleshooting on the internet I could find.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Safford, AZ
- Parts Used:
- 00645038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Poor cleaning of dishes and calcium build up on filter
I watch utube to assess the problem then took eveything apart and saw the build up on the filter, which i had never cleaned. I tried to clean it but was unsuccessful so order the filter from partselect and it came within a couple of days, installed very easily and began to clean as it always had.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from AUBURN, IN
- Parts Used:
- 00611320
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
dishwasher not emptying tub, dirty dishes when the dishwasher said the cycle was done
easy repair, but the check valve wasn't the problem, it was the float switch that isn't on the tech sheet in the dishwasher or mentioned as a possible culprit anywhere I could find on the internet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from LEXINGTON, KY
- Parts Used:
- 00645038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Filter-Micro was clogged with lime from hard water.
Replacement was fast and very simple. Was completed in less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from LAWRENCEVILLE, GA
- Parts Used:
- 10006917
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken lock
Followed instructions from YouTube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from EDINA, MN
- Parts Used:
- 00645038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Over the years the filter became too clogged with embedded particles
Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Parkesburg, PA
- Parts Used:
- 00656340
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rubber insulating plate broke into two pieces
Removed a screw on each side of the bottom of the front of the dishwasher to remove 2 metal plates holding the rubber insulating plate in place.
After laying old and new insulation plate side-by-side, as a reference, I used a long piece of Alien tape to hold new insulating plate in place on back metal plate and flipped rubber over metal plate and placed other metal plate in place.
Laid down on my belly and attached plates using both screws again underneath the dishwasher door.
Pulled down the rubber insulating plate towards the floor and pulled off the glue stripe on the back.
Opened the dishwasher door all the way then closed it and the rubber insulating plate went into place and I pressed along the bottom to seal the glue strip.
After laying old and new insulation plate side-by-side, as a reference, I used a long piece of Alien tape to hold new insulating plate in place on back metal plate and flipped rubber over metal plate and placed other metal plate in place.
Laid down on my belly and attached plates using both screws again underneath the dishwasher door.
Pulled down the rubber insulating plate towards the floor and pulled off the glue stripe on the back.
Opened the dishwasher door all the way then closed it and the rubber insulating plate went into place and I pressed along the bottom to seal the glue strip.
Was this instruction helpful to you?
Thank you for voting!