SHU33A06 Bosch Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Phyllis from CLERMONT, FL
- Parts Used:
- 00494772
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Water leak on top of door.
Went to on line video and followed it. The old gasket came right out and the new one fit right in. Started at the top middle and worked the gasket in on both sides to make sure it was evenly spaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from WOODINVILLE, WA
- Parts Used:
- 00425458
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Dish washer would fill and leak when not in use
Turn off power to unit!
-Remove kick panel,2 screws.
-remove water valve, 2 screws, 3 electrical connections, 1 hose clamp.
-Remove elbow from old valve and install on the new valve ( use teflon pipe tape)
-replace valve, hose & hose clamp, electrical connectors and water supply line.
Scew unit in place ,2 screws.
Check for leaks then replace kick panel, 2 screws.
-Remove kick panel,2 screws.
-remove water valve, 2 screws, 3 electrical connections, 1 hose clamp.
-Remove elbow from old valve and install on the new valve ( use teflon pipe tape)
-replace valve, hose & hose clamp, electrical connectors and water supply line.
Scew unit in place ,2 screws.
Check for leaks then replace kick panel, 2 screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from EAST JORDAN, MI
- Parts Used:
- 00618605
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Wrench set
BROKEN CORD, PART OF DOOR COUNTERWEIGHT
REMOVED DISHWASHER FROM CABINET. DETACHED BASE FROM BODY OF THE DISHWASHER. INSTALLED NEW CORD, REATTACHED BASE TO BODY OF DISHWASHER AND REINSTALLED IN CABINET. OPINION: THIS IS A LENGTHY REPAIR AND UNNECESSARY ONE. THE CORD IS PART OF THE DOOR COUNTERWEIGHT AND SUBJECT TO TENSION EVERY TIME THE DOOR IS OPENED, AS WELL AS POTENTIAL CHAFFING DUE TO PROXIMITY TO VARIOUS METAL PARTS, AND VIBRATION. THE CORD SHOULD BE MADE OF STRONGER MATERIAL AND ARMORED OR ALLOWED MORE CLEARANCE. BOSCH SHOULD FIX TO LAST THE LIFE OF THE DISHWASHER.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andy from STOWE, PA
- Parts Used:
- 00425458
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Water was leaking into the dishwasher when it was not running and leaking onto the floor
Disconnected the water and power, pulled dishwasher out from under the counter, unscrewed the old inlet valve, disconnected hose from exit of inlet valve, noted the placement of the wires and disconnected them. Installed new inlet valve in reverse order and reinstalled dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from FREDERICKSBRG, PA
- Parts Used:
- 00499500
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Overfill then no fill
Remove bottom kick plate and raise the feet up. Remove attachment from the top to counter. Slide out. Facing the unit, remove left hand side sheet metal cover. The unit is behind this cover. Unhook the hose on the lower end. Pop the new one in and hook it up!! Test on quick rinse and see results. If ok return to normal as disassembled. Make sure to level the unit after tucking it back in. Enjoy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Seattle, WA
- Parts Used:
- 00494772
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water leakage from the dishwasher; unknown source.
Followed the video on your site and it was an easy install with no more leakage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue E from CARMEL, IN
- Parts Used:
- 00166623
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Rinse aid dispenser lid would not stay closed
Use a screwdriver flat blade to pry up one edge of closed lid. Put one side of lid into hinge and snapped other side into place. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danette from SANTA FE, NM
- Parts Used:
- 00165314
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing/broken wheel on right side of lower dishwasher rack
I snapped the part in and voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from NEW PARIS, IN
- Parts Used:
- 00166623
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lid for the streak treatment wouldn't stay shut.
Use screwdriver to gently wedge the side of the dispenser body apart enough to pop out the old kid, then insert the new kid in it's place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from PENN VALLEY, PA
- Parts Used:
- 00615079
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Clogged, old filter- dirty dishes
Removed old filter and replaced with new filter. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ranaye from BECKER, MN
- Parts Used:
- 00165256
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Not getting water
shut off water, pull dishwasher out, took side insulation off, unhooked what was connected to the float switch and replaced the new with the old. Reconnected everything and put insulation back and wa-la , all done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tommy from McArthur, CA
- Parts Used:
- 00239144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Watch the video
Parts perfect works perfect
Was this instruction helpful to you?
Thank you for voting!