SHE6AP12UC ((06)) Bosch Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from LINCOLN, DE
- Parts Used:
- 00617087
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
wheel (one of eight) missing from lower rack
Slip the wheel onto the axle, snap the clip facing up onto the frame
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from BIRMINGHAM, AL
- Parts Used:
- 00622058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Drain Pump runs continuously - inlet valve leaking into bottom tray
disconnected inlet hose and water line from sink, removed old inlet valve and installed new valve and reconnected inlet hose and water line from sink - checked for leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from NORTH HALEDON, NJ
- Parts Used:
- 00622058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
The valve allowed water to fill the dishwasher when not in use.
This was the third time I replaced a fill valve in a Bosch diswasher, twice in this unit and once in a previous unit. I read the installation hints on your web site and want to add the following suggestion.
The notes on your web site say you can remove the valve from behind the toe face and pull it out to reach the hose and plug. I found that the Bosch designers called for both the hose and wire to on the short side. I found that pulling the dishwasher forward 6" to 9" allows you to access these connections from the side at least to hold them while making the connection. I hope this helps. Thank you, Bill
The notes on your web site say you can remove the valve from behind the toe face and pull it out to reach the hose and plug. I found that the Bosch designers called for both the hose and wire to on the short side. I found that pulling the dishwasher forward 6" to 9" allows you to access these connections from the side at least to hold them while making the connection. I hope this helps. Thank you, Bill
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harper from Charleston WV, WV
- Parts Used:
- 00669221
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Dishwasher was pouring water during the rinse cycle. put the machine up on milk crates to find the source of the leak. The water was coming from the bottom corner of the door. Fount the orig gasket torn
Remove the dishwasher from under the counter. Remove door springs. On the inside of the lip of the door remove the 6 screws that hold the outer door panel on, and remove panel. this will expose hinge screws. Remove the two screws per side holding the inner door to the hinge assembly. Take pictures of the way the gasket's grey plastic end cap assembles between the inner door frame and the hinge, and remove the inner door. The old gasket has a channel lip that sits on the plastic edge of the washer tub, pull it off this lip and discard. Install new gasket and put it all back together! Use this opportunity to clean the gunk out of the upper door seals.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TONY from PALMDALE, CA
- Parts Used:
- 00622058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
No water in machine, can not wash dishes.
Turn off water, disconnect power cord, remove front kickplate. Remove 2 screws that hold the water inlet valve, pull it out, disconnect electrical connection, disconnect water supply.. Check the inlet valve with volt-ohm meter for continuity. If it is good, then the valve is stuck shut. The ohm reading should be in the 900-1100 range. Replace valve, installation is the reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from LAWRENCEVILLE, GA
- Parts Used:
- 10006917
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken lock
Followed instructions from YouTube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from AUBURN, IN
- Parts Used:
- 00611323
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dishwasher not draining, dishes dirty
replacing the sensor was simple, just unplug and turn it out, but didn't solve the problem, it's a float sensor that doesn't show up on the tech sheet in the dishwasher or anywhere in troubleshooting on the internet I could find.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from WESTMINSTER, CO
- Parts Used:
- 00611332
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher would not start and had not completely drained.
Tried the door lock first. Did not fix the problem.
Replaced the drain pump and it fixed the problem.
Parts Select identified the pump as the most frequent problem.
Next time I will order both parts when one is cheap for any repair.
Find Parts Select is very helpful. They have identified a problem with a washing machine in the past.
I will use them for future problems.
Replaced the drain pump and it fixed the problem.
Parts Select identified the pump as the most frequent problem.
Next time I will order both parts when one is cheap for any repair.
Find Parts Select is very helpful. They have identified a problem with a washing machine in the past.
I will use them for future problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John D from Ocoee, FL
- Parts Used:
- 00611332
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
E-24
Removed old discharge pump and replaced it with the new one. After four attempts the dishwasher worked once. This cycle continued for the next 3 attempts then it stoped all together. Ordered the sensor, installed it snd the dishwasher still doesn’t work! Now what do I do???
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from MONTROSE, CO
- Parts Used:
- 00611295
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
On/Off button not working properly
Turned power off, disconnected plug from switch, R&R switch, reconnected plug and restored power
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from TAMPA, FL
- Parts Used:
- 00649332
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
racks rusting
replaced left upright unfortunately I ordered 2 left and now I still need the right Wish they would have caught that on the order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from AUBURN, IN
- Parts Used:
- 00611320
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
dishwasher not emptying tub, dirty dishes when the dishwasher said the cycle was done
easy repair, but the check valve wasn't the problem, it was the float switch that isn't on the tech sheet in the dishwasher or mentioned as a possible culprit anywhere I could find on the internet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from ELGIN, TX
- Parts Used:
- 00669221
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
the door has to be taken apart.
My son and my husband did it. I watched.
They both injured their fingers.
But it stopped the leak!
They both injured their fingers.
But it stopped the leak!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from PERU, NY
- Parts Used:
- 00617087
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing wheel on the lower shelf of the dishwasher made it difficult to slide in and out.
The wheel easily snapped in.
Was this instruction helpful to you?
Thank you for voting!