Models
>
1149-0-580327112
1149-0-580327112 Craftsman Generator
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
This is a genuine OEM approved replacement fuel filter which is specially designed for use with gas-powered lawn and garden equipment. Its purpose is to ensure the fuel that is supplied into the engin...
In Stock
Order now and your part arrives by Apr 10
$27.80
This fuel valve with bushing fits a variety of outdoor equipment and allows the fuel to smoothly flow into the gas engine. The bushing part is pressed into the hole provided in the fuel tank and the f...
In Stock
Order now and your part arrives by Apr 10
$8.23
This is a genuine OEM sourced replacement part designed for use with a variety of lawn and garden equipment. This item fits the cylinder and helps to provide an air tight seal to prevent any leaks. It...
In Stock
Order now and your part arrives by Apr 10
$9.24
This is a Genuine Manufacturer Sourced replacement part used on a a variety of Engines. This is a Fuel Line Connector connects the fuel line to the carburetor. This part is made out of Plastic and Met...
In Stock
Order now and your part arrives by Apr 10
$19.75
This starter pulley, also known as a recoil starter pulley, is sourced from the original manufacturer for use in outdoor power equipment. It includes the starter rope and plastic spool to hold the rop...
In Stock
Order now and your part arrives by Apr 10
This authentic manufacturer rewind starter spring is a replacement part used in various power equipment engines. It is connected to a pulley system, and it is found inside the starter housing. It is a...
No Longer Available
$6.51
This is a Genuine OEM replacement part used on variety of Lawn and Garden Equipment Engines. This part is made out of Rubber and it is sold individually. If the carburetor is leaking fuel it is recomm...
In Stock
Order now and your part arrives by Apr 10
$48.92
This starter clutch is an authentic OEM replacement part used in small outdoor power engines. Each package includes one clutch and one ball bearing. The starter clutch allows the engine to start by en...
In Stock
Order now and your part arrives by Apr 10
$63.68
It is an authentic amature-magneto (ignition coil) which was specially designed for use with Briggs and Stratton engines used on lawn and garden equipment. The purpose of this item is to deliver elect...
In Stock
Order now and your part arrives by Apr 10
$16.83
An authentic OEM replacement fuel line that is specially produced for use with gas powered endings commonly installed on generators and other equipment. The fuel line is used to deliver the fuel from ...
On Order
$7.16
The exhaust gasket attaches to the exhaust manifold and helps to form a seal. It is an authentic OEM sourced part which is specially designed for use with Briggs & Stratton generators and engines, plu...
In Stock
Order now and your part arrives by Apr 10
$10.78
This genuine part is sourced directly from the original equipment manufacturer. It is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The p...
In Stock
Order now and your part arrives by Apr 10
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 1149-0-580327112
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from PICAYUNE, MS
- Parts Used:
- 192980GS
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from RADFORD, VA
- Parts Used:
- 192980GS
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank ... Read more r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank ... Read more r />
used same technique to insert valve upward into bushing
works great!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from LEES SUMMIT, MO
- Parts Used:
- 192980GS
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Was this instruction helpful to you?
Thank you for voting!