Models > CE200SP2WD01

CE200SP2WD01 Uni Cooktop

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for CE200SP2WD01

Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
This OEM drip bowl fits under 8-inch burner elements and has a diameter of approximately 10-inches. Drip bowls catch any spills, and are a quick, easy, and cheap way to improve your cooktop aesthetic....
In Stock
This drip bowl is an OEM approved replacement part designed for use with various electric ranges and cooktops. This part is located underneath the burner to contain any spills while cooking. It fits ...
In Stock
This kit comes with the necessary components to replace your burner terminal block. It includes interchangeable mounting brackets, a terminal box, ceramic wire nuts, heat shrink protective tubing, and...
In Stock
If the burner element on your range is damaged or no longer heating up, the element should be replaced. When you remove the element, check the terminals for any signs of corrosion or arcing. If you fi...
In Stock
This is a genuine OEM 6-inch burner element for your electric range or cooktop. If the element is no longer heating up, it may be time for a replacement. When you remove the old element, inspect the t...
In Stock
This switch controls the stove top surface burner.
In Stock
$66.76
Sold individually.
Special Order
Special Order
Special Order
Special Order
$375.98
Special Order
$315.33
Special Order

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for CE200SP2WD01

Viewing 3 of 3
Element will not heat
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing
How to fix it
Oven not heating evenly
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
George from New Port Richey, FL
Parts Used:
5303935086
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
High heat reluctant to turn down.
Most of the job is simple fastener mechanics.
Use a nut driver or Phillips screwdriver. Remove rear panel.

Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.

Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.

Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.
45 of 49 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Melvin from Attica, MI
Parts Used:
5303935086
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Right front burner would over-heat
First of all I removed the top panel then removed the switch. I then took pictures of the switch & drew a sketch with all the info. Then I went to your web site, matched up the switch & ordered.
When the switch arrived I went thru the above replacing the bad switch.
23 of 27 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from hollywood, FL
Parts Used:
5303935058
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
corroded terminals
was more of a job of splicing wires together than anything else. Loved the heat shrink electrical tubing
to put over the wires for insulation. used a hair
dryer. must buy more of that amazing stuff
22 of 24 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!