85RB-4K Magic Chef Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Frank from Pierce, ID
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The grommets came apart metal from rubber.
I replaced the broken grommets with the new ones. I purchased 8 so I would have back ups because I did not feel the new one would last either. I think they cost TOO MUCH but I could not haggle for price.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from wildomar, CA
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
range top loose, grommets missing
very easy to push each grommet into range top holes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Rochester, NY
- Parts Used:
- WP74002414, 74002413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
igniter would no longer work, it would stick
pull knob off streight out. remove two phillips head screws, disconnect wire to disassemble. To reassemble reattatch wire to replacement igniter, screw in two phillips head screws and push on the knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hal from National City, CA
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing gromet
Pushed into hole by hand, really simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Prosser, WA
- Parts Used:
- 12001296
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Igniter wouldnt turn- knob spinning on shaft
Pull knob off igniter shaft, remove two screws, take out igniter, unplug wire. Reverse to install. Would have been very simple except the metal insert that is supposed to be inside the new knob was missing from the kit. I tried using the old insert in the new knob but it did not fit tight enough and would spin on the shaft. Had to use the old worn knob on the new igniter. Customer service said they don't carry the inserts. What? The brand new knob is useless! Needed to get the stove fixed so I didn't bother returning the entire kit. Oh well, stove works now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Vacaville, CA
- Parts Used:
- 12001296
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
igniter not working on magic chef stove on 60 foot yacht
called and ordered the part. it arrived the next day. amazing. put it in and all was well./ another happy yacht owner.
Tim Wiest
Tim Wiest yacht Service
Tim Wiest
Tim Wiest yacht Service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ARCHER, FL
- Parts Used:
- 74002413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Wouldn't ignite
Pulled knob,removed 2 screws removed wire,removed old ignitor repl. With new reversed procedure,done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONNA from WARREN, PA
- Parts Used:
- WP74002414
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old knob is broken
This item had to be returned. Didn"t fit. Our shaft is shorter, and the new knob would not stay on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from GOODLETTSVLLE, TN
- Parts Used:
- 12001296
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Generated no spark
Remove 2 screws and 1 wire reinstall same with new switch and knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Santa Paula, CA
- Parts Used:
- 12001296
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitor shaft and knob sheered
This is a small RV cooktop. There is no pilot light but each burner will light using the spark type ingitor twist knob. Raise the front of the stove cooktop. It is on a hinge. Replace the ignitor assembly using existing screws. There is a very small anchor pin on the ignitor assy. which protrudes 1/16" from the base. The anchor pin hole had not been drilled into the stove face plate which prevents the ignitor assembly from twisting when engaged. So I drilled a 3/16 anchor pin hole exactly where required. It is important to be exact so as to align the installation screw holes in the face plate. These holes can be enlarged if need be however. Align the pin with the anchor hole and install the 2 existing screws. Attach the ignitor lead to the ignitor assy. and install the new knob. Close the stove top and start cooking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Brownwood, TX
- Parts Used:
- 12001296
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top burners would not ignite
Removed igniter wire, 2 screws, removed old igniter and reversed procedure, checked spark
and then lit burner. Easy, Easy
and then lit burner. Easy, Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Elk City, OK
- Parts Used:
- 12001296
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ignitor was not functioning properly.
I removed the igniter cable from the old knob. Removed 2 screws and the old knob, installed the new knob with 2 screws and plugged in the igniter cable. Works like a CHAMP!!! Must be an Oklahoma State University Football igniter and knob!! 2001 Big 12 Champions!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Millersburg, MI
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost on of the Rubber Grommet holding the stove grate
So simple would be embarrassed to give any instructions; it is so self evident.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Richwood, OH
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
original grommets broken
The new grommets were NOT the correct parts, too big, so there was no repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Plymouth, MA
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber grommet for stove top cover
I ordered the grommet... Didn't match the others ... But it fit on , and will do the job
Was this instruction helpful to you?
Thank you for voting!