KGCS166GSS10 KitchenAid Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Corinth, TX
- Parts Used:
- WP3191922
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the knob was melted by a hot pan
popped off the old knobs and put on the new ones in less than a minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roland from Houston, TX
- Parts Used:
- WP9782116
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Igniter problem on one gas burner
I had to remove the two separate components of the gas burner unit, each had two screws. I lifted then tilted the lower portion of the burner unit to allow access to the underside of the igniter. I removed the wire and then with an offset screwdriver I removed the single screw that held the igniter in place. I reversed the steps to install the replacement, very quick fix.
I was also very pleased with how quickly the order was processed and the part was delivered, only three or four days with standard shipping.
I was also very pleased with how quickly the order was processed and the part was delivered, only three or four days with standard shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymundo from Cerritos, CA
- Parts Used:
- WP4456901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
I had a faulty wiring on the igniter switches.
replaced the set of igniter switches I order from Partselect .com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Williamsburg, VA
- Parts Used:
- WP9782116
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace Gas Cooktop bad surface Igniter
1. Turn off Gas at valve under cooktop. Unplug electric to igniters. 2. Remove all control knobs. 3. Remove grates and burner covers. 4. Remove screws from each burner head (10 screws) 5. lift and remove cooktop cover. 6. Reach under cabinet and push up main cooktop body (about 4 or 5 inches) and BLOCK. 7. AT FRONT OF COOKTOP REMOVE 2 philips screws holding burner strip. Slightly lift burner strip enough to get short handle philips under screw holding igniter (Be gentle as gas line is still connect and will give enough so as not to have to disconnect them. 8. Remove and replace igniter. 9. Reverse procedures above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie F from McKinney, TX
- Parts Used:
- WP9782116
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
one of the cooktop burners would not ignite
removed knobs, burnners, top cover plate, disconnecte two gas lines from burnners to controls, lifted burnner bar, unscrewed igniter, installed new ingiter, and then reassembled cooktop. There was a total of ten screws removed, and two gas lines disconnected. The total repair time was about twenty minutes. I ordered the part on line and it was at my home in less than 48 hours. Happy ending the cooktop works great, and the repair cost only equaled the cost of the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Traci from Bozeman, MT
- Parts Used:
- WP3191922
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Had melted knob on cooktop
Went great, part was perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from CHANDLER, AZ
- Parts Used:
- WP9759513
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original burner grates had deteriorated and two side burner grates and the center grates were replaced.
The burner grates for the KitchenAid range are no longer available from KitchenAid. Other burner grates available in PartSelect were a like-kind fit. Installation was easy--just replace the burner grates.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jodie from Carlsbad, CA
- Parts Used:
- WP3191922
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner knob appeared to have been accidentally melted by placing a hot pot on top of it.
I took the melted knob off, located the part # went online and found this site. I immediately found the correct burner knob, ordered it, and it came very quickly to my home! I just popped it right on the cooktop, and it's as good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JUDY from AIKEN, SC
- Parts Used:
- WP3191922
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
control knob was melted from a hot pan
Easy as 1 2 3. Removed ruined knob and set new knob on post. That's it. Complete success!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from Georgetown, TX
- Parts Used:
- WP3191922
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner knobs needed replacing due to hot pan melting them
Simiply pulled the old burner knob off and replaced them with the new knobs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Colorado Springs, CO
- Parts Used:
- 4454571
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Stove top did not come with a gas regulator and nipple attachment
A plummer did the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Olalla, WA
- Parts Used:
- WP3192741
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
change over from Natural Gas to LP and install cooktop from Electric to gas
removed old electric cooktop and install gas line and gas cooktop and change from natural gas to LP remove and replace orifice with new ones from kit, my cooktop called for 2 black orifices in the two small burners but did not come in the parts kit that I orded so I used 2 red orifices and it seems to work just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Saint Charles, IL
- Parts Used:
- WP9782116
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
no spark on surface of gas stove
repair failed; after much difficulty in accessing the small bolts that hold the 'spark igniters' in place; rear two were more accessible, front two proved impossible. Next step, invest in a new slide-in stove. The repair was a dad guess on my part; although designers often consider repair as a non-option, -sad but true.
Was this instruction helpful to you?
Thank you for voting!