KGCP483KSS05 KitchenAid Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Roland from Houston, TX
- Parts Used:
- WP9782116
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Igniter problem on one gas burner
I had to remove the two separate components of the gas burner unit, each had two screws. I lifted then tilted the lower portion of the burner unit to allow access to the underside of the igniter. I removed the wire and then with an offset screwdriver I removed the single screw that held the igniter in place. I reversed the steps to install the replacement, very quick fix.
I was also very pleased with how quickly the order was processed and the part was delivered, only three or four days with standard shipping.
I was also very pleased with how quickly the order was processed and the part was delivered, only three or four days with standard shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from BROKEN ARROW, OK
- Parts Used:
- W10185266
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
replace pads or feet on steel grate of gas stove
pull old ones out of legs. need to glue new ones in, they fit too loose. Some kits contain glue. get some high temp head gasket cement. a drop on each one is plenty. I used some old porcelain glue and hope it will hold. the pads are 2 bucks each plus shipping so don't let them get away!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Williamsburg, VA
- Parts Used:
- WP9782116
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace Gas Cooktop bad surface Igniter
1. Turn off Gas at valve under cooktop. Unplug electric to igniters. 2. Remove all control knobs. 3. Remove grates and burner covers. 4. Remove screws from each burner head (10 screws) 5. lift and remove cooktop cover. 6. Reach under cabinet and push up main cooktop body (about 4 or 5 inches) and BLOCK. 7. AT FRONT OF COOKTOP REMOVE 2 philips screws holding burner strip. Slightly lift burner strip enough to get short handle philips under screw holding igniter (Be gentle as gas line is still connect and will give enough so as not to have to disconnect them. 8. Remove and replace igniter. 9. Reverse procedures above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie F from McKinney, TX
- Parts Used:
- WP9782116
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
one of the cooktop burners would not ignite
removed knobs, burnners, top cover plate, disconnecte two gas lines from burnners to controls, lifted burnner bar, unscrewed igniter, installed new ingiter, and then reassembled cooktop. There was a total of ten screws removed, and two gas lines disconnected. The total repair time was about twenty minutes. I ordered the part on line and it was at my home in less than 48 hours. Happy ending the cooktop works great, and the repair cost only equaled the cost of the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Saint Charles, IL
- Parts Used:
- WP9782116
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
no spark on surface of gas stove
repair failed; after much difficulty in accessing the small bolts that hold the 'spark igniters' in place; rear two were more accessible, front two proved impossible. Next step, invest in a new slide-in stove. The repair was a dad guess on my part; although designers often consider repair as a non-option, -sad but true.
Was this instruction helpful to you?
Thank you for voting!