KGCT305AAL1 KitchenAid Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Waterford, MI
- Parts Used:
- WP4454392
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Sparker would not quit sparking after lighting the gas.
Turned off the gas then disconnected the gas line. Unplugged the AC cord and removed the unit from the counter top. Had to locate a suitable area to lay the cooktop, rather large. The bottom cover is held on by 6-8 sheet metal screws, however, the gas regulator and nipple must be removed also for the cover to come off. I removed the Igniter module screws, leaving the wires connected and mounted the new module in it's place. I then removed one wire at a time from the old and put it on the new part. Replaced the back cover and reinstalled the gas regulator with fresh pipe sealant. Probably took an hour including cleaning the top and counter top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Martinsville, IN
- Parts Used:
- WP3185804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
There was a crack in the porcelain not letting it spark
I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire.
Then just connected the new electrode and place the assy, in the burner.
Then just connected the new electrode and place the assy, in the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from San Bruno, CA
- Parts Used:
- WP3185804
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
broken ignitor insulation; repeated sparking after burner lit
Disconnected gas & electric connections; lifted unit out of countertop onto padded table upside down. Unscrewed ~16 sheet metal screws for access. Removed bad ignitor by driving off retaining clip. Had to remove burner (3 screws) for access to install retaining clip on new ignitor. Reassembled, reinstalled. Works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Middletown, NJ
- Parts Used:
- WP3182568
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced Stove knob
Removed old one, installed new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Lake Wylie, SC
- Parts Used:
- 4175422
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Grate pads fell off- burner scratched surface-need special glue
Bought in auto repair store special black glue used for sealing gaskets. Husband needed to use latex gloves, toothpicks, ice pick, and small screw driver to glue and install new burner pads.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from COLORADO SPGS, CO
- Parts Used:
- W10854242
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plastic anchor tips broken.
Removed the broken items and replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wade from Jacksons Gap, AL
- Parts Used:
- WP3185804
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Spark Ignition Electrode was not sparking properly
Used a pair of pliers and pulled firmly on ignit. elect. till the retaining clip pulled off the bottom of the elect.The wire pulled off the bottom of it and I had to use a long- thin- nose set of needlenose pliers to pull the wire out of where the elect. came out.Plugged wire in place and snapped electrode back in place without using the retainer clip.Works great.Thanks Wade
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sylvia from DELANO, CA
- Parts Used:
- WP3182568
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
2 control knobs were broken.
I just replaced the broken knobs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from RAINIER, WA
- Parts Used:
- WP3180081
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob skirt clips (2 of 4) broken
Gently pressed the lower two clips onto my thumbs as I pressed the skirt into the cooktop skirt hole. Be gentle or you can break the new skirt!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from LAKEWOOD, CO
- Parts Used:
- WP4454392
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
spark module failure, wouldn't spark.
The repair was fairly straightforward, much easier the second time around. The first part was defective. (irregular spark). I reordered and installed the new one. It works, but nowhere near as good as the original.The problem is that the frequency of the spark on these replacement modules is only once per second. To get technical, the gas as presented to the spark is turbulent, causing several sparks to occur before the ideal mixture coincides with the spark. Needless to say, there is an excess of gas wafting around the kitchen until it lights, sometimes in excess of 20 seconds. NOT SAFE! Our BBQ and fireplace insert spark orders of magnitude faster than this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from POST, TX
- Parts Used:
- WP3180081
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Grommet broken
Good
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sequim, WA
- Parts Used:
- WP3180081
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the little tabs that hold the skirt in the hole break off
I pulled the knobs off, lifted the broken skirts out and snapped the new ones in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelly J from KAPLAN, LA
- Parts Used:
- WP3185804
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
igniter on top right front burner was shorting out,it would click but not ignite burner
removed igniter and found porcelin split in half. JB welded both halves and put back into slot ,works fine now. Bought two extra in case.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marcus from CARSON, CA
- Parts Used:
- WP3182569
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken burner control knob
pull old knob off install new knob
Was this instruction helpful to you?
Thank you for voting!