KGCT365BBL3 KitchenAid Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sabrina from Mooresville, NC
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
several grate pads fell out/lost /broke during cleaning
The only real issue was locating the proper adhesive to ensure that the new pads would not fall out. The small insert paper slip in the package noted that a RTV adhesive should be used. After much searching at the home improvement super store, I learned it would be found at an auto supply store. It is black, and is for high temp use. It is available in a small tube for around $2.00. The RTV is usually used to make gaskets for heat/oil exposure in auto repair. I did have trouble removing a broken stub from a pad that had broken off in the hole. I used an awl to get what I could and push the rest into the hole deeper, then insert a new pad with along with the adhesive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Waterford, MI
- Parts Used:
- WP4454392
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Sparker would not quit sparking after lighting the gas.
Turned off the gas then disconnected the gas line. Unplugged the AC cord and removed the unit from the counter top. Had to locate a suitable area to lay the cooktop, rather large. The bottom cover is held on by 6-8 sheet metal screws, however, the gas regulator and nipple must be removed also for the cover to come off. I removed the Igniter module screws, leaving the wires connected and mounted the new module in it's place. I then removed one wire at a time from the old and put it on the new part. Replaced the back cover and reinstalled the gas regulator with fresh pipe sealant. Probably took an hour including cleaning the top and counter top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Martinsville, IN
- Parts Used:
- WP3185804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
There was a crack in the porcelain not letting it spark
I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire.
Then just connected the new electrode and place the assy, in the burner.
Then just connected the new electrode and place the assy, in the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from San Bruno, CA
- Parts Used:
- WP3185804
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
broken ignitor insulation; repeated sparking after burner lit
Disconnected gas & electric connections; lifted unit out of countertop onto padded table upside down. Unscrewed ~16 sheet metal screws for access. Removed bad ignitor by driving off retaining clip. Had to remove burner (3 screws) for access to install retaining clip on new ignitor. Reassembled, reinstalled. Works like new!
Was this instruction helpful to you?
Thank you for voting!
burner grate pads came off over time and were lost, knob skirt clips had broken
attached grate pads with GE clear silicone caulk (withstands heat) to burners. skirts just snap in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from The Woodlands, TX
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber pads on bottom of grate broke off, grate was scratching stainless steel top
I just put the grate pads in the bottom of the grate. The repair was a snap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Middletown, NJ
- Parts Used:
- WP3182568
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced Stove knob
Removed old one, installed new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Denver, CO
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing bumper pads
Original bumper pads NOT glued into the burner grates. Hence they began to disappear during routine use and cleaning. Very simple repair with a little glue this time around. But fairly expensive for a very small part set
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rio Rancho, NM
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
grate pads not available from kitchen aide
Been looking for grate pads for 10 years and finally found you site and part # WPL 814323.
Wasn't sure that they would fit but couldn't even find new grates so decide to try them --Fit perfect.
Kitchen aide stove top gas with round grates. Used the drill to clean out the holes with broken pads still embedded.With clean holes the new pads just screwed in like the originals. Thank you very much
Wasn't sure that they would fit but couldn't even find new grates so decide to try them --Fit perfect.
Kitchen aide stove top gas with round grates. Used the drill to clean out the holes with broken pads still embedded.With clean holes the new pads just screwed in like the originals. Thank you very much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Palm Desert, CA
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pads melt and fall out of the burner grate
cleaned out pad area with an awl. then the pads just slide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joe from des plaines, IL
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing grate pads
remove grate - flip upside down - be sure holes are clean and dry - using toothpick, swab some RTV sealant into the holes and a bit on the pads ... insert pads till they seat - be sure to hold in place till all air is evacuated - wipe excess RTV with paper towel...DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wade from Jacksons Gap, AL
- Parts Used:
- WP3185804
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Spark Ignition Electrode was not sparking properly
Used a pair of pliers and pulled firmly on ignit. elect. till the retaining clip pulled off the bottom of the elect.The wire pulled off the bottom of it and I had to use a long- thin- nose set of needlenose pliers to pull the wire out of where the elect. came out.Plugged wire in place and snapped electrode back in place without using the retainer clip.Works great.Thanks Wade
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from LATON, CA
- Parts Used:
- 814323
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rubber grate pads that protect the range top had worn and were flat.
It didn't. The grate pads (PN# PS389174) were too small for the grate (W10311216) and wouldn't work. (PN# recommended by Whirlpool parts department) The pads were smaller in diameter and shorter. Yes I could have glued them in, but because of the size the pads would be flat in no time. The only thing I could order from KitchenAid was the total grate. I ordered the pads late December, they were backordered. I got them the 1st week of February. I tried getting through to Whirlpool by calling to see if there was something I could reorder, but no luck, couldn't through. Am I unhappy? Oh some, but I handle it. Its not the first time I have been rode hard and put away wet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from COLORADO SPGS, CO
- Parts Used:
- W10854242
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Plastic anchor tips broken.
Removed the broken items and replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from RAINIER, WA
- Parts Used:
- WP3180081
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob skirt clips (2 of 4) broken
Gently pressed the lower two clips onto my thumbs as I pressed the skirt into the cooktop skirt hole. Be gentle or you can break the new skirt!
Was this instruction helpful to you?
Thank you for voting!